HP Integrity rx5670 Hardware Installation Guide - HP Integrity rx5670 (A6837B/ - Page 27

Replacing the Processor Extender Board, Installing Memory, Memory Load Order,

Get HP Integrity rx5670 PDF manuals and user guides View all HP Integrity rx5670 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Figure 2-8 Processor Connector Alignment Tabs Alignment Tabs Installing Additional Components Installing Processors and Memory procsoctabs Replacing the Processor Extender Board To replace the processor extender board, perform the following steps: 1. Ensure the extraction levers (see Figure 2-6) are positioned in the outward, unlocked position. 2. Align the processor extender board with the front and rear card guides. The end of the board which is closer to the CPU module(s) should be toward the front of the server chassis. 3. Slide the processor extender board down until it begins to seat in the socket located on the system baseboard. 4. Push the extraction levers inward to the locked position to fully seat the processor extender board. Installing Memory Memory Load Order DIMMs are installed on memory extender boards located in the top service bay. If only one memory extender board is installed, it must be located in slot 0. (See Figure 2-5.) A maximum of two memory extender boards may be installed per system. Each memory extender board can hold up to 24 DIMMs. DIMMs of different size can be installed on a memory extender board, but they must be grouped by size. By replacing the DIMMs in your server, or installing additional DIMMS, you can increase the amount of memory in your server. Several different DIMM sets are available. The DIMMs are listed in your hp Integrity rx5670 Operation and Maintenance Guide, and at http://www.hp.com (search for keyword rx5670). Chapter 2 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Chapter 2
Installing Additional Components
Installing Processors and Memory
27
Figure 2-8
Processor Connector Alignment Tabs
Replacing the Processor Extender Board
To replace the processor extender board, perform the following steps:
1. Ensure the extraction levers (see Figure 2-6) are positioned in the outward, unlocked position.
2. Align the processor extender board with the front and rear card guides. The end of the board which is
closer to the CPU module(s) should be toward the front of the server chassis.
3. Slide the processor extender board down until it begins to seat in the socket located on the system
baseboard.
4. Push the extraction levers inward to the locked position to fully seat the processor extender board.
Installing Memory
Memory Load Order
DIMMs are installed on memory extender boards located in the top service bay. If only one memory extender
board is installed, it must be located in slot 0. (See Figure 2-5.) A maximum of two memory extender boards
may be installed per system. Each memory extender board can hold up to 24 DIMMs. DIMMs of different size
can be installed on a memory extender board, but they must be grouped by size.
By replacing the DIMMs in your server, or installing additional DIMMS, you can increase the amount of
memory in your server. Several different DIMM sets are available. The DIMMs are listed in your
hp Integrity
rx5670 Operation and Maintenance Guide
, and at http://www.hp.com (search for keyword rx5670).
procsoctabs
Alignment Tabs