HP Integrity rx5670 Hardware Installation Guide - HP Integrity rx5670 (A6837B/ - Page 65

Management Processor Commands, Reset BMC passwords

Get HP Integrity rx5670 PDF manuals and user guides View all HP Integrity rx5670 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Cable Connections Core I/O Connections 9. The current link state information is displayed. When prompted to enter a new value or Q, just hit enter. The message "-> Current Link State has been retained" will be displayed. 10. A new lc listing is displayed, including the values entered in the preceding steps. Verify that the desired values have been accepted. When prompted to enter a parameter for revision, Y to confirm, or Q to Quit, enter Y to confirm all parameters. 11. Observe the following display: -> LAN Configuration has been updated -> Reset MP (XD command option 'R') for configuration to take effect. MP Host Name: name (the name entered in step 5) MP:CM> 12. Enter XD -reset to reset the MP. 13. After the MP resets, log into the MP again. Then enter the MP command mode (enter CM at the MP: prompt). 14. At the MP:CM> prompt, enter LS to confirm the new LAN settings. 15. Enter SA to enable/disable web console and telnet access after the MP has been reset. Management Processor Commands Table 4-1 Management Processor Commands and Descriptions Command BP CA CG CL CM CTRL-B CO CSP DATE DC DF DI FW HE ID IT LC Description Reset BMC passwords Configure asynch/serial ports Certificate generator View console log Select command mode Return to MP main menu Select console mode Connect to service processor Date display Default configuration Display FRU information Disconnect remote or LAN console Upgrade MP firmware Display help for menu or command System information Inactivity timeout settings LAN configuration Chapter 4 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Chapter 4
Cable Connections
Core I/O Connections
65
9. The current link state information is displayed. When prompted to enter a new value or Q, just hit
enter
.
The message “-> Current Link State has been retained” will be displayed.
10. A new lc listing is displayed, including the values entered in the preceding steps. Verify that the desired
values have been accepted. When prompted to enter a parameter for revision, Y to confirm, or Q to Quit,
enter
Y
to confirm all parameters.
11. Observe the following display:
-> LAN Configuration has been updated
-> Reset MP (XD command option ‘R’) for configuration to take effect.
MP Host Name: name (the name entered in step 5)
MP:CM>
12. Enter
XD -reset
to reset the MP.
13. After the MP resets, log into the MP again. Then enter the MP command mode (enter
CM
at the MP:
prompt).
14. At the MP:CM> prompt, enter
LS
to confirm the new LAN settings.
15. Enter
SA
to enable/disable web console and telnet access after the MP has been reset.
Management Processor Commands
Table 4-1
Management Processor Commands and Descriptions
Command
Description
BP
Reset BMC passwords
CA
Configure asynch/serial ports
CG
Certificate generator
CL
View console log
CM
Select command mode
CTRL-B
Return to MP main menu
CO
Select console mode
CSP
Connect to service processor
DATE
Date display
DC
Default configuration
DF
Display FRU information
DI
Disconnect remote or LAN console
FW
Upgrade MP firmware
HE
Display help for menu or command
ID
System information
IT
Inactivity timeout settings
LC
LAN configuration