HP LH4r HP Netserver 10/100TX PCI LAN Adapter Guide - Page 20

Novell NetWare 4.1x or 4.2 Only

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Chapter 5 Configuring the Adapter and Installing Drivers (press Esc) the manual install and return to the NWConfig screen.) 11. Select Save parameters and load driver to continue. 12. For each additional adapter you want to install, respond to the prompt and then repeat steps 7-11. 13. To complete the driver installation process, press the Esc key until you arrive back at the Installation Options screen. 14. To return to the console prompt, choose Exit. NOTE If the adapter cannot transmit or receive following the installation, you may need to modify the frame type in the AUTOEXEC.NCF file. Novell NetWare 4.1x or 4.2 Only Use the NetWare install program to install the HP NetServer 10/100 adapter driver in Novell NetWare 4.1x. For Novell NetWare 3.11, 3.12 and 3.2, see the ReadMe files. The following procedure is a condensed description of the installation process: NOTE Prior to installing, either load DOS or NetWare drivers from your computer's CD-ROM drive or create a floppy disk from the HP NetServer 10/100TX PCI LAN Adapter Drivers CD using the MAKEDISK.BAT utility. See the Making a Setup Floppy Disk section earlier in this guide. 1. From the NetWare console, type LOAD INSTALL and press Enter. 2. From the Installation Options screen, choose Driver options and press Enter. 3. Choose Configure network drivers and press Enter. If any drivers are already loaded, a list of them appears. 4. Choose Select an additional driver and press Enter. A 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Chapter 5
Configuring the Adapter and Installing Drivers
12
(press
Esc
) the manual install and return to the NWConfig
screen.)
11.
Select
Save parameters
and load driver to continue.
12.
For each additional adapter you want to install, respond to
the prompt and then repeat steps 7-11.
13.
To complete the driver installation process, press the
Esc
key until you arrive back at the Installation Options screen.
14.
To return to the console prompt, choose
Exit
.
NOTE
If the adapter cannot transmit or receive
following the installation, you may need to
modify the frame type in the
AUTOEXEC.NCF
file.
Novell NetWare 4.1x or 4.2 Only
Use the NetWare install program to install the HP NetServer
10/100 adapter driver in Novell NetWare 4.1x. For Novell
NetWare 3.11, 3.12 and 3.2, see the ReadMe files. The
following procedure is a condensed description of the
installation process:
NOTE
Prior to installing, either load DOS or
NetWare drivers from your computer’s
CD-ROM drive or create a floppy disk from
the
HP NetServer 10/100TX PCI LAN
Adapter Drivers
CD using the
MAKEDISK.BAT
utility. See the
Making a
Setup Floppy Disk
section earlier in this
guide.
1.
From the NetWare console, type
LOAD INSTALL
and
press
Enter
.
2.
From the Installation Options screen, choose
Driver
options
and press
Enter
.
3.
Choose
Configure network drivers
and press
Enter
. If
any drivers are already loaded, a list of them appears.
4.
Choose
Select an additional driver
and press
Enter
. A