HP LH4r HP Netserver 10/100TX PCI LAN Adapter Guide - Page 51

Fast Ethernet Wiring, Power Management

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Chapter 10 Technical Information 2. Click the Adapters tab. 3. Under the "Network Adapters" field, highlight the adapter you're removing and click the Remove button. 4. Click OK. 5. Follow the instructions in the section Installing the Adapter in the NetServer at the start of this manual. Fast Ethernet Wiring The 100BASE-TX specification supports 100 Mbps transmission over two pairs of Category 5 twisted-pair Ethernet (TPE) wiring. One pair is used for transmit and the other for receive. Segment lengths are limited to 100 meters with 100BASE-TX for signal timing reasons. This complies with the EIA 568 wiring standard. Power Management The selections are ACPI and APM. ACPI should work in most computers. The APM selection will pre-enable the Wake-on-LAN function of the adapter. Set this selection to APM if one of the following apply: 1. You are having difficulty with remote wake-up in computers that are compliant with the PCI 2.2 specification. You are running an OS that is not ACPI (Advanced Control and Power Interface) aware and you are not using the 3-pin header cable. 2. You are running an ACPI aware OS (such as Windows 98) on a non-ACPI computer and the link light goes out when you shut down the system, disabling Wake-on-LAN. 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Chapter 10
Technical Information
43
2.
Click the
Adapters
tab.
3.
Under the “Network Adapters” field, highlight the adapter
you’re removing and click the
Remove
button.
4.
Click
OK
.
5.
Follow the instructions in the section
Installing the
Adapter in the NetServer
at the start of this manual.
Fast Ethernet Wiring
The 100BASE-TX specification supports 100 Mbps
transmission over two pairs of Category 5 twisted-pair Ethernet
(TPE) wiring. One pair is used for transmit and the other for
receive. Segment lengths are limited to 100 meters with
100BASE-TX for signal timing reasons. This complies with the
EIA 568 wiring standard.
Power Management
The selections are ACPI and APM. ACPI should work in most
computers.
The APM selection will pre-enable the Wake-on-LAN function
of the adapter. Set this selection to APM if one of the following
apply:
1.
You are having difficulty with remote wake-up in
computers that are compliant with the PCI 2.2
specification. You are running an OS that is not ACPI
(Advanced Control and Power Interface) aware and you are
not using the 3-pin header cable.
2.
You are running an ACPI aware OS (such as Windows 98)
on a non-ACPI computer and the link light goes out when
you shut down the system, disabling Wake-on-LAN.