HP LH4r HP Netserver LC 2000 Compaq Rack Install Guide
HP LH4r - NetServer - 256 MB RAM Manual
View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals |
HP LH4r manual content summary:
- HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 1
HP NetServer LC 2000 Installation Guide for Compaq® Model 4000/ 7000 Series Racks HP Part Number 5969-5949 Printed in December 1999 - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 2
Packard shall not be liable for errors contained herein or for incidental or use or reliability of its software on equipment that is not furnished guide is for the person who installs, administers, and troubleshoots network servers. Hewlett-Packard Company assumes you are qualified in the servicing - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 3
NetServer in the Rack 21 Attaching the Cable Management Arm 26 Attaching the Front Bezel Adapter 28 Attaching the Front Bezel 29 Continuing with the Rack Installation Process 30 4 Warranty and Support 31 Hardware Accessories Limited Warranty 31 HP Repair and Telephone Support 32 Index...33 - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 4
- HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 5
describes how to mount an HP NetServer LC 2000 into a Compaq® model 4000- or 7000-series rack. Refer to the HP NetServer LC 2000 Installation Guide that came with the NetServer for instructions on adding accessories to, and configuring the NetServer. HP NetServer - Compaq Rack Precautions CAUTION - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 6
those listed above. See the "Warranty and Support" section of this document for additional support considerations. Safety Precautions Always keep the following safety and environmental issues in mind, especially if you install the HP NetServer in a Compaq rack: l Optimum Operating Environment - The - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 7
) Recessed mounting brackets Slide Slide mounting flange Removable plastic fascia panel that covers entire front of the NetServer. This NetServer includes two bezels: one for installation in HP rack enclosures, and one for installation in Compaq 4000/7000 series rack enclosures. Display and buttons - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 8
- HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 9
how to remove the top cover and the pedestal from the HP NetServer LC. WARNING Before removing the top cover, shut down the to a shock hazard from telephone ringing voltages. Tools Required l An anti-static service kit (3M 8501/8502/8503 or equivalent). This kit includes a static-dissipating work - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 10
all users and if necessary back-up files. 2. Follow instructions in your network operating system (NOS) documentation to gracefully shut down all networking software and applications. 3. Press the power switch on the HP NetServer's control panel when prompted by the operating system. Normally, this - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 11
of the chassis and two metal tabs, which fit into two slots on the bottom front of the chassis. Figure 2-1. Removing the HP NetServer LC 2000 Bezel CAUTION To prevent damage to the covers, support the cover as you remove it from the HP NetServer. The NetServer's covers can be easily damaged. 7 - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 12
Chapter 2 Prepare the HP NetServer for Rack-Mounting Removing the Top Cover 1. Remove the single screw that secures the top cover to the front of the NetServer. 2. Slide the top cover forward to disengage the mounting brackets. 3. Lift the top cover off (See Figure 2-2). Top Cover Screw Hole - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 13
for Rack-Mounting Removing the Pedestal The pedestal version of the HP NetServer LC 2000 mounts to an anti-tip pedestal, which must be removed to mount the server in a rack. NOTE The front bezel is shown removed, but the bezel may remain on the chassis while removing the pedestal. 1. Disconnect - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 14
- HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 15
3 Rack-Mounting the HP NetServer This chapter explains how to mount the HP NetServer in a Compaq model 4000- or 7000-series rack enclosure. Figure 3-1 shows a Compaq model 4000- or 7000-series rack. Side Stabilizing "Feet" (Both Sides) Front Stabilizing " - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 16
HP Rack Installation Road Map and the HP NetServer LC 2000r Rack Cabling Reference Guide. NOTE If the HP NetServer HP NetServer at the customer's site, installation of the network operating system and other software may occur after the HP NetServer is mounted in the rack. WARNING The HP NetServer - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 17
components are to be mounted in the rack below the HP NetServer, install those components before starting to mount the NetServer. NOTE Use the HP Rack Configuration Tools to determine where in the rack to mount the HP NetServer. The tools are available at: http: //www.hp.com/netserver/support 13 - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 18
Chapter 3 Rack-Mounting the HP NetServer 1. Use the marking pen to mark the 2nd and 14th holes on both front columns, as shown on the template. See Figure 3-2. NOTE The two - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 19
Chapter 3 Rack-Mounting the HP NetServer "#" represents the EIA unit numbers on the rack columns. # # the Column Adapters and Slides 1. Make sure that anti-tip precautions have been taken before installing servers in the rack. 2. Align the right column adapter to the right front column. 3. Match - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 20
Slide Mount Column Left Adapter Front Column Adapter Bottom of HP NetServer Figure 3-5. Mounting Column Adapter to Front Columns 6. Reposition the front brackets on the slides. See Figure 3-6. a. Remove the nuts from the two front slide screws. . b. - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 21
Chapter 3 Front Rack-Mounting the HP NetServer Figure 3-6. Repositioning the Front Bracket 7. Reposition the rear brackets on the slides. See Figure 3-7. a. Loosen the nuts on the two front slide screws. . b. Move the - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 22
Chapter 3 Rack-Mounting the HP NetServer 8. Hold a slide in position inside the two left-hand rack columns and observing the following items. a. The mounting flange on each end of the slide - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 23
Chapter 3 Rack-Mounting the HP NetServer 9. With the slide pushed firmly into position, insert two screws through the slide's front bracket into the captive nuts on the left 2000. 3. Push back to insert the mounting prongs on the hinge assembly bracket into the slots in the side of the server. 19 - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 24
Chapter 3 Rack-Mounting the HP NetServer 4. Install and tighten the two Phillips screws as shown in Figure 3-9. Follow steps 3 and 4 to attach the catch mechanism on the right side of the LC 2000. Figure 3-9. Attaching the Hinge Assembly and Catch Assembly 20 - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 25
sheet metal mounting handles to the sides of the server. Each handle requires two Phillips head screws. See Figure 3-10. Figure 3-10. Attaching the Mounting Handles Placing the HP NetServer in the Rack Use this procedure to position the HP NetServer into the extended slides and secure the chassis - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 26
. This locked position prevents the slides from moving back into the rack, unless the release latches are pressed as shown in Figure 3-13. 4. Lift the HP NetServer by its four handles off the floor. 5. Move the rear of the - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 27
Figure 3-12. The mounting tabs in the slides will engage the slots in the chassis. See Figure 3-13. Channel(2) Figure 3-12. Mounting the HP NetServer on the Slides 7. Lower the NetServer onto the slide members. See Figure 3-12. The handles will temporarily support the NetServer on the slides. 23 - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 28
Chapter 3 Rack-Mounting the HP NetServer 8. Adjust the NetServer's position on the slide members to the slides. 10. Use a T-15 Torx driver to remove the screws holding the handles to the NetServer. See Figure 3-13. 11. Take the handles off the NetServer and store the handles and screws in a - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 29
Chapter 3 Rack-Mounting the HP NetServer The handles can be re-attached whenever you remove the NetServer from the rack. If moving the NetServer elsewhere, always package it with the handles attached. 12. Press in the release latches on each slide, and push the NetServer all the way into the rack. - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 30
this face of the left rear column. 14th Hole from Bottom 12th Hole from Bottom 9th Hole from Bottom 7th Hole from Bottom Bottom of HP NetServer Figure 3-15. Attaching the Cage Nuts to the Left Column 3. Orient the Cable Management Arm as shown in Figure 3-16. 4. Match the inner flange mounting - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 31
out of the rack to ensure the Cable Management Arm moves along with the chassis without binding. NOTE Refer to the HP NetServer LC 2000r Rack Cabling Reference Guide, for information about cable dressing and routing. 8. If the Cable Management Arm moves with the chassis and the rack installation - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 32
Chapter 3 Rack-Mounting the HP NetServer 10. Plug the HP NetServer's power cable and all available data cables into the back of the NetServer. Attaching the Front Bezel Adapter The front bezel adapter fits the front bezel properly in the Comaq rack. Attach the front bezel adapter by pushing - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 33
adapters are the only items requiring installation on the rack, which is done before mounting the rack slides. 1. Position the Bezel in front of the HP NetServer LC 2000r as shown in Figure 3-18. Blue Tab Slide Securing Screws(2) Hinge Pins (3) Figure 3-18. Hinge Pins and Blue Tab Release 29 - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 34
down on the blue Bezel Release Tab shown in Figure 3-19. Figure 3-19. Attaching the Bezel to the NetServer 3. Press the bezel onto the front of the HP NetServer and release the Blue Tab to engage the hinge pins. See Figures 3-18 and 3-19. 4. Swing the open bezel to the right to engage - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 35
HP NetServer Warranty and Service/Support Booklet provided with your system documentation for the warranty limitations, customer responsibilities, and other terms and conditions. Hardware Accessories Limited Warranty An HP NetServer Hardware Accessory is an HP hardware product that is specifically - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 36
Chapter 4 Warranty and Support HP Repair and Telephone Support Refer to the HP NetServer Warranty and Service/Support Booklet supplied with your HP NetServer system documentation for instructions on how to obtain HP repair and telephone support. 32 - HP LH4r | HP Netserver LC 2000 Compaq Rack Install Guide - Page 37
NetServer rack installation, 21 HP NetServer rack-mounting preparation, 5 Mounting handles, attaching, 21 Precautions, Compaq rack, 1 Precautions, safety, 2 Rack Mount Parts List, 13 Rack Mounting the HP NetServer, 11 Removing Bezel, 7 Removing Pedestal, 9 Removing Top Cover, 8 service, 31 support
HP NetServer LC 2000
Installation Guide
for
Compaq
®
Model 4000/ 7000
Series Racks
HP Part Number 5969-5949
Printed in December 1999