HP LH4r HP Netserver LH Pro NetRAID Installation Guide - Page 16

To install the HP NetRAID Adapter at Systems A and B

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Part 1: Installing Additional Hardware Components 4. Connect the free end of the C11 cable from the CD-ROM drive to the 50- pin output connector on the top hot swap cage. The output connector is on the left when the cage is viewed from the back. 5. Remove the C23 cable from the SCSI B controller connector and coil the cable up out of the way. 6. Remove the C22 cable from channel 0 of the NetRAID card and connect it to SCSI B. 7. Set the DIP switches on the back of the hot swap cages as shown below. Note the DIP switches are off when they are set to the left. U‚ƒÃ8htrÃTv‡pu 7‚‡‡‚€Ã8htrÃTv‡pu Iˆ€ir… Q‚†v‡v‚ Iˆ€ir… Q‚†v‡v‚  RII  RII  RII  RII  RII  RII  RQ  RII  RQ  RQ  RII  RQ 8. Replace the LH Pro cover and bezel. You have now completed hardware installation on the LH Pros and are ready to proceed to Part 2: "Setting up the HP Storage System/6". Installing the HP NetRAID Adapter You are now ready to connect the HP NetRAID Adapter to the battery backup module, and then to install the HP NetRAID Adapter (model number D4943A). The battery backup module is a mezzanine card already in place on the HP NetRAID Adapter. To install the HP NetRAID Adapter at Systems A and B: 1. Plug the connector on the wire leading from the lower left corner of the battery backup module into the connector as shown below. Battery Backup Module with Disconnected Battery Pack HP NetServer LH Pro Microsoft Cluster Installation Guide - 1 October 1997 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
Part 1: Installing Additional Hardware Components
HP NetServer LH Pro Microsoft Cluster Installation Guide - 1 October 1997
7
4.
Connect the free end of the C11 cable from the CD-ROM drive to the 50- pin output connector on the top
hot swap cage.
The output connector is on the left when the cage is viewed from the back.
5.
Remove the C23 cable from the SCSI B controller connector and coil the cable up out of the way.
6.
Remove the C22 cable from channel 0 of the NetRAID card and connect it to SCSI B.
7.
Set the DIP switches on the back of the hot swap cages as shown below.
Note the DIP switches are off when they are set to the left.
8.
Replace the LH Pro cover and bezel.
You have now completed hardware installation on the LH Pros and are ready to proceed to Part 2: "Setting up the
HP Storage System/6".
Installing the HP NetRAID Adapter
You are now ready to connect the HP NetRAID Adapter to the battery backup module, and then to install the HP
NetRAID Adapter (model number D4943A). The battery backup module is a mezzanine card already in place on the
HP NetRAID Adapter.
To install the HP NetRAID Adapter at Systems A and B:
1.
Plug the connector on the wire leading from the lower left corner of the battery backup module into the
connector as shown below.
Battery Backup Module with Disconnected Battery Pack