HP LH4r HP Netserver LT 6000r Rack Cabling Guide - Page 37

Procedure for Connecting and, Routing Cables to the LT 6000r

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

3 Procedure for Connecting and Routing Cables to the LT 6000r Step 1: Prepare to Cable the HP NetServer LT 6000r Assess How Components Will be Connected to the Server You may find the following steps to be helpful before you begin cabling: • Review the layout of the rack installation generated with Hewlett-Packard rack configuration tools, such as Rack Assistant (available at www.hp.com/go/netservers). • Consider the cabling guidelines discussed in Chapter 2 of this Reference Guide, in the section "Data Cabling References and Guidelines." • Review the plan for your rack power subsystem, considering how you will provide failure resistance (see Appendix B on the Redundant Switch), interim power (see Table 2-1 on Uninterruptible Power Supplies) and distribution (see the section of Chapter 2 titled "Power Distribution Units"). Check that you have completed the mounting of the Cable Guides, Cable Management Arms, and Power Distribution Units as noted below. See Figure 2-2 for an example illustration showing how these three items may look when mounted. Attach Cable Guide to Rack Column Using the instructions included, attach the two Cable Guides to the rack column. Mount the Cable Management Arm The HP NetServer LT 6000r includes a Cable Management Arm. Mount the arm by following the instructions in the HP NetServer LT 6000/6000r Installation Guide which accompanies your unit. Cable routing details are included in the section of this chapter titled "Cable Management." 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
33
3
Procedure for Connecting and
Routing Cables to the LT 6000r
Step 1: Prepare to Cable the HP NetServer
LT 6000r
Assess How Components Will be Connected to the Server
You may find the following steps to be helpful before you begin cabling:
•
Review the layout of the rack installation generated with Hewlett-Packard
rack configuration tools, such as Rack Assistant (available at
www.hp.com/go/netservers
).
•
Consider the cabling guidelines discussed in Chapter 2 of this
Reference
Guide
, in the section "Data Cabling References and Guidelines."
•
Review the plan for your rack power subsystem, considering how you will
provide failure resistance (see Appendix B on the Redundant Switch),
interim power (see Table 2-1 on Uninterruptible Power Supplies) and
distribution (see the section of Chapter 2 titled "Power Distribution
Units").
Check that you have completed the mounting of the Cable Guides, Cable
Management Arms, and Power Distribution Units as noted below. See Figure 2-2
for an example illustration showing how these three items may look when
mounted.
Attach Cable Guide to Rack Column
Using the instructions included, attach the two Cable Guides to the rack column.
Mount the Cable Management Arm
The HP NetServer LT 6000r includes a Cable Management Arm. Mount the arm
by following the instructions in the
HP NetServer LT 6000/6000r Installation
Guide
which accompanies your unit.
Cable routing details are included in the
section of this chapter titled "Cable Management."