HP LH4r NetWare Installation Guide

HP LH4r - NetServer - 256 MB RAM Manual

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

HP LH4r manual content summary:

  • HP LH4r | NetWare Installation Guide - Page 1
    EISA .cfg files DSK Files for the HP SCSI Driver NetWare Duplexing Mirroring and Drive Sizes SCSI CD-ROM BusTech SCSI Controller Guide I. Before Installing NetWare Logical Disk Size for the Disk Array Controller Booting from the Embedded SCSI controller II. Installing the HP NetServer SCSI Drivers
  • HP LH4r | NetWare Installation Guide - Page 2
    NetWare and HP NetRAID Drivers on a New HP NetServer Installing NetWare and HP NetRAID Drivers on an HP NetServer Already Setup with NetWare Section 3. HP LAN Card J3171A Installation Guide Installing the J3171A LAN Card Driver on NetWare 3.12 Installing the J3171A LAN Card Driver on NetWare
  • HP LH4r | NetWare Installation Guide - Page 3
    on setting up a duplexed system, see the NetWare Installation manual.) Mirroring and Drive Sizes The D2076B 1 GB hard disk is slightly smaller than the previous model, D2076A. This difference in size may cause problems if you are duplexing the entire drive. SCSI CD-ROM Use the cdrom3.exe patch
  • HP LH4r | NetWare Installation Guide - Page 4
    driver. Interrupts (IRQS) to Avoid Some systems may not work well when the LAN card is configured to use interrupts 2, 7, 9, or 15. IRQ 2 and 9 are cascading interrupts, NetWare uses 7 and 15 as software 4.1 with the HP JetSet Utility, you first create two logical drives (partitions) in JetSet:
  • HP LH4r | NetWare Installation Guide - Page 5
    manual or the NetWare Support Encyclopedia, or call your nearest Novell Authorized Service Center. For a more detailed information on NOS installation and configuration, see the NetServer Information Assistant, provided on a CD-ROM with your NetServer. Section 2. NetWare Installation Guide
  • HP LH4r | NetWare Installation Guide - Page 6
    access to your CD-ROM drive by installing the appropriate ASPI drivers. Create the NetWare 3.12 SCSI Drivers Diskette 1. Boot the HP NetServer with the HP NetServer Navigator CD-ROM. 2. Follow the instructions to create a driver diskette. Label the diskette "HP NetServer MS DOS and Novell NetWare
  • HP LH4r | NetWare Installation Guide - Page 7
    DOS=HIGH Load the Drivers 1. Reboot the system. 2. Remove the HP NetServer Navigator CD-ROM and insert the NetWare 3.12 CD-ROM. 3. Follow the NetWare 3.12 Installation and Upgrade documentation to create a SERVER.312 subdirectory on drive C. 4. After the system loads SERVER.EXE (automatically as
  • HP LH4r | NetWare Installation Guide - Page 8
    the server. 6. Continue to the end of the installation process. Installing the SCSI Drivers on NetWare 4.10 1. Create the Drivers Diskette and install the CD-ROM drive for the DOS environment as explained in "Installing the SCSI Drivers on NetWare 3.12" above. 2. Remove the HP NetServer Navigator
  • HP LH4r | NetWare Installation Guide - Page 9
    controllers, LAN cards) and the software drivers for accessory hardware. Follow the instructions listed below that relates to the specific hardware installed make sure that you use HP Navigator and run EISA Config to set the MP SPEC. to 1.4. ◊ Hard Disk Controllers, LAN Cards: ∗ The installation
  • HP LH4r | NetWare Installation Guide - Page 10
    hard disk drives, must already be configured using the EISA Configuration Utility. Installing the HP Disk Array Controller Driver on NetWare 3.12 1. Boot the HP NetServer using the HP NetServer Navigator CD-ROM. 2. Follow the instructions to create a driver diskette. Label the diskette "HP NetServer
  • HP LH4r | NetWare Installation Guide - Page 11
    install. 6. Follow the on-line instructions to install the HPDA driver to drive C: When you see the Enter Server Directory screen, type: C:\SERVER.312 The install utility copies HPDA drivers and information related to the disk array to drive C. 7. Remove the HP NetServer Navigator CD-ROM and insert
  • HP LH4r | NetWare Installation Guide - Page 12
    instructions from the HP NetServer Navigator to configure NetRAID disk array and create a drivers diskette. The following procedures refer to this diskette as the "Drivers Diskette". NOTE Configuring HP NetRAID includes configuring the type of array you want to use and initializing the hard drives
  • HP LH4r | NetWare Installation Guide - Page 13
    the instructions from the HP NetServer Navigator to configure NetRAID disk array and create a drivers diskette. The following procedures refer to this diskette as the "Drivers Diskette". NOTE Configuring HP NetRAID includes configuring the type of array you want and initializing the hard drives
  • HP LH4r | NetWare Installation Guide - Page 14
    the instructions from the HP NetServer Navigator to configure NetRAID disk array and create a drivers diskette. The following procedures refer to this diskette as the "Drivers Diskette". NOTE Configuring NetRAID includes configuring the type of array you want and initializing the hard drives
  • HP LH4r | NetWare Installation Guide - Page 15
    are installing HP NetRAID drivers on an HP NetServer already setup and running NetWare. NetWare 3.12 and HP NetRAID Drivers 1. Down the server. 2. Insert the HP NetRAID adapter, cable, and disk array drives. 3. Boot the HP NetServer using the HP NetServer Navigator CD 4. Follow the instructions to
  • HP LH4r | NetWare Installation Guide - Page 16
    . NetWare 4.10 and HP NetRAID Drivers 1. Down the server. 2. Insert the HP NetRAID adapter, cable, and disk array drives. 3. Boot the HP NetServer using the HP NetServer Navigator CD 4. Follow the instructions to configure the HP NetRAID disk array and create a drivers diskette for NetWare 4.10
  • HP LH4r | NetWare Installation Guide - Page 17
    J3171A Installation Guide Use the instructions listed here if you have an HP NetServer LD Pro bundled with the HP J3171A 10/100 TX Fast Ethernet PCI LAN card. To install J3171A drivers in NetWare environment follow the steps: 1. Boot the server and insert the HP NetServer Navigator in the CD drive
  • HP LH4r | NetWare Installation Guide - Page 18
    . Follow the instructions below for the specific version of NetWare that you've installed: Installing the J3171A LAN Card Driver on NetWare 3.12 For NetWare 3.12, the system will not search for LAN card drivers. You have to do it manually: When install exits to the system console: 1. Down the server
  • HP LH4r | NetWare Installation Guide - Page 19
    one matching driver for a PCI LAN controller: Install found the following hardware but found more that one driver supporting this hardware: PCI.8086.1229.0000.0000.01 Press for a list of drivers to choose from or to continue 1. Press key 2. High light the driver HPTX.LAN (HP 10
  • HP LH4r | NetWare Installation Guide - Page 20
    in HP NetServer LX with 4GB memory needs a special procedure. Follow the instruction closely to avoid system hang problem. 1. Install NetWare 4.11/IntranetWare, with memory less than 2GB, as described in the previous sections. 2. Install NetWare 4.11/IntranetWare Support Pack v2.0. The Support Pack
  • HP LH4r | NetWare Installation Guide - Page 21
    HP Network Server Division BBS: 408-553-3500 Section 6. HP NetServer CD Status Report FAX HP has a new FAX service to ensure that you have access to the newest versions of HP NetServer system software. To obtain an HP NetServer CD Status Report via FAX, perform the following: 1. Call the HP FIRST
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
HP NetServer LD Pro, LH, LH Plus, LH Pro, LS, LX Pro,
LXe Pro
NetWare Installation Guide
May 15, 1997
This document presents the most important information that you need to install
NetWare.
The first part of this document is a list of helpful tips on NOS installation, the second
part is a step-by-step installation guide.
Please see the CD-ROM-based
HP Information Assistant
for additional detailed
information to help you in installing NetWare.
Table of Contents
Section 1. Installation Tips
Create a DOS Partition
EISA .cfg files
DSK Files for the HP SCSI Driver
NetWare Duplexing
Mirroring and Drive Sizes
SCSI CD-ROM
BusTech SCSI Controller
Network Interface Cards (NICs)
Interrupts (IRQS) to Avoid
Packet Receive Buffers
Setting Volume Disk Block and Cache Buffer Sizes
Creating Partitions on the Disk Array
Large Volume Sizes and NetWare 4.11/IntranetWare
Section 2. NetWare Installation Guide
I.
Before Installing NetWare
Logical Disk Size for the Disk Array Controller
Booting from the Embedded SCSI controller
II. Installing the HP NetServer SCSI Drivers on NetWare 3.12, 4.10, and
4.11/IntranetWare
Requirements
Installing the SCSI Drivers on NetWare 3.12