HP Latex 850 HP Scitex LX850 & LX820 Printer: Installation Guide - Page 32

Choose delta or star (Y) configuration, Install the power jumpers, CAUTION

Get HP Latex 850 PDF manuals and user guides View all HP Latex 850 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

+LJKWULSKDVHYROWDJHFRQILJXUDWLRQ 9  /RZWULSKDVHYROWDJHFRQILJXUDWLRQ ±9 25 A 40 A 1 Japan may have input frequencies of 50 Hz or 60 Hz voltage measured between phases  9ROWDJHOLQHWROLQH 4. Close the fuse holder until you feel and hear a "click." The red square above the fuse holder should change color once all fuse holders have been inserted. Install the power jumpers 1. There are five power jumpers supplied. Select the appropriate power jumper according to the single-phase power at the installation site. Inserting the wrong power jumper will cause the vacuum pump to work incorrectly. 2. Insert the correct power jumper into the connector, located close to the transformer. Choose delta or star (Y) configuration Manpower 1 person Tools T10 and M15 screwdriver, M7 wrench Time 5 minutes There are two Delta/Star terminal blocks located on the printer that must be configured. Use the following table to make the configuration, and follow the procedures below to access the two terminal blocks. CAUTION: Both Delta/Star terminal blocks must use the same configuration. 28 Chapter 6 Configure the electrical system ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
4.
Close the fuse holder until you feel and hear a “click.” The red square above the fuse holder should
change color once all fuse holders have been inserted.
Install the power jumpers
1.
There are five power jumpers supplied. Select the appropriate power jumper according to the
single-phase power at the installation site. Inserting the wrong power jumper will cause the vacuum
pump to work incorrectly.
2.
Insert the correct power jumper into the connector, located close to the transformer.
Choose delta or star (Y) configuration
Manpower
Tools
Time
1 person
T10 and M15 screwdriver, M7 wrench
5 minutes
There are two Delta/Star terminal blocks located on the printer that must be configured. Use the following
table to make the configuration, and follow the procedures below to access the two terminal blocks.
CAUTION:
Both Delta/Star terminal blocks must use the same configuration.
28
Chapter 6
Configure the electrical system
ENWW
25 A
40 A
1
Japan may have input frequencies of 50 Hz or 60 Hz voltage measured between phases