Home » HP Manuals » Printers » HP Metal Jet 3D » Manual Viewer

HP Metal Jet 3D User Guide - Page 382

Broken lines such as the one in this eample are acceptable, but they must cross the whole

Add to My Manuals
Save this manual to your list of manuals

Page 382 highlights

7. A second pattern is printed on the cleaning roll. This pattern is more fine, as to try to refine the distance selected with the coarse pattern. When instructed, open the cover to evaluate the pattern. 8. Once again, check the lines on the right side of the pattern and count the number of complete lines, as illustrated in the blue box in the following image. The number of lines can range from zero (no complete lines) to seven. In the following example, there are four visible line. NOTE: Broken lines such as the one in this eample are acceptable, but they must cross the whole width of the cleaning roll. IMPORTANT: If the number to be entered in this finer adjustment is 0 becaause there are no complete lines, the calibration will fail. In this case, contact your support representative. 378 Chapter 7 Troubleshooting

Section	Page
Introduction	5
Welcome to your HP Metal Jet S100 system	5
Powder workflow	6
Safety precautions	14
Main components	33
Networking	47
Connectivity requirements—remote monitoring	47
Configuration	48
Troubleshooting	49
Supplies	50
Printer	50
How to recycle supplies	70
System operation	72
Printing system	72
Process Parameters glossary	83
Process Parameters glossary for the HP Metal Jet S100 Curing station	84
Preventive maintenance	93
Safety precautions	93
General cleaning instructions	93
Maintenance resources	94
Printing system maintenance	107
User calibrations	309
Move or store the product	311
Extended downtime	311
Customer Self-Repair	313
Cleaning parts and the Build Unit	335
Cleaning parts	335
Coarse cleaning and powder recovery	335
Fine cleaning	343
Thermal conditioning of metal powder	343
Troubleshooting	348
Printing system troubleshooting	348
System errors	388
Introduction	388
0030-0003-0084 SVS - Printhead cleaning roll slippage	388
0030-0009-0059 Service Station – Spittoon motor stall	389
0030-0009-0085 Service Station – Spittoon motor friction too high (with cartridge)	389
0030-0006-0002 Service Station – Spittoon roller not detected	389
0050-0028-0202 Cooling – Top enclosure safety filter (user end – left) not detected	389
0050-0028-0102 Cooling – Top enclosure safety filter (service end – right) not detected	389
0085-0003-0X10 Carriage – Printhead interconnect PCA – Voltage out of range	390
0085-0008-0X46 Carriage – Printhead – Not calibrated, misaligned, unable to calibrate	390
0085-0008-0X81 Carriage – Printhead – Bad Acumen access	390
0085-0008-0X82 Carriage – Printhead – Data not responding	390
0085-0008-0X83 Carriage – Printhead – Mismatch	391
0085-0008-0X85 Carriage – Printhead – Fails logical	391
0085-0008-0X86 Carriage – Printhead – Temperature too high	391
0085-0008-0X87 Carriage – Printhead – Temperature too low	391
0085-0008-0X89 Carriage – Printhead – Wrong model	392
0085-0008-0X93 Carriage – Printhead – Fails continuity	392
0085-0008-0X94 Carriage – Printhead – Temperature extremely high	393
0085-0008-0X95 Carriage – Printhead – Temperature extremely low	393
0085-0008-0X96 Carriage – Printhead – Energy calibration failure	393
0085-0008-0X98 Carriage – Printhead – Transmit error	394
0085-0013-0X01 Carriage – Primer – Malfunction	394
0085-0013-0X33 Carriage – Primer – Current too high	394
0085-0013-0X41 Carriage – Primer – Leakage	395
When you need help	396
Request support	396
Service information	396
Accessibility	397
Front panel	397
Curing time	397

Match case Limit results 1 per page

A second pattern is printed on the cleaning roll. This pattern is more fine, as to try to refine the

distance selected with the coarse pattern. When instructed, open the cover to evaluate the pattern.

Once again, check the lines on the right side of the pattern and count the number of complete lines,

as illustrated in the blue box in the following image. The number of lines can range from zero (no

complete lines) to seven. In the following example, there are four visible line.

NOTE:

Broken lines such as the one in this eample are acceptable, but they must cross the whole

width of the cleaning roll.

IMPORTANT:

If the number to be entered in this finer adjustment is 0 becaause there are no

complete lines, the calibration will fail. In this case, contact your support representative.

378

Chapter 7

Troubleshooting