HP Pavilion dv3 HP Pavilion dv3 Entertainment PC - Maintenance and Service Gui - Page 71

Power connector cable, Remove the two Phillips PM2.5×5.0 screws

Get HP Pavilion dv3 PDF manuals and user guides View all HP Pavilion dv3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Power connector cable NOTE: The power connector cable is included in the Cable Kit, spare part number 603924-001. 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 38), and then remove the following components: a. Memory module/wireless module compartment cover (see Memory module on page 39) b. Optical drive (see Optical drive on page 50). c. Top cover (see Top cover on page 51) d. USB board (see USB board on page 60) Remove the power connector cable: 1. Disconnect the power cable (1) from the system board. 2. Release the power cable from the clips(2) built into the base enclosure. 3. Remove the two Phillips PM2.5×5.0 screws (3) that secure the power connector and bracket to the base enclosure. 4. Remove the power connector bracket (4). The power connector bracket is included in the Bracket Kit, spare part number 603925-001. 5. Release the power connector (5) from the clip built into the base enclosure. Reverse this procedure to install the power connector cable. Component replacement procedures 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Power connector cable
NOTE:
The power connector cable is included in the Cable Kit, spare part number 603924-001.
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see
Battery
on page
38
), and then remove the following components:
a.
Memory module/wireless module compartment cover (see
Memory module
on page
39
)
b.
Optical drive (see
Optical drive
on page
50
).
c.
Top cover (see
Top cover
on page
51
)
d.
USB board (see
USB board
on page
60
)
Remove the power connector cable:
1.
Disconnect the power cable
(1)
from the system board.
2.
Release the power cable from the clips
(2)
built into the base enclosure.
3.
Remove the two Phillips PM2.5×5.0 screws
(3)
that secure the power connector and bracket to
the base enclosure.
4.
Remove the power connector bracket
(4)
. The power connector bracket is included in the
Bracket Kit, spare part number 603925-001.
5.
Release the power connector
(5)
from the clip built into the base enclosure.
Reverse this procedure to install the power connector cable.
Component replacement procedures
61