HP ProLiant BL420c HP ProLiant BL420c Gen8 Server Blade Maintenance and Servic - Page 31

Dimms

Get HP ProLiant BL420c PDF manuals and user guides View all HP ProLiant BL420c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

DIMMs IMPORTANT: This server blade does not support mixing LRDIMMs, RDIMMs, or UDIMMs. Attempting to mix any combination of these DIMMs can cause the server to halt during BIOS initialization. To identify the DIMMs installed in the server blade, see "DIMM identification (on page 76)." To remove the component: 1. Power down the server blade (on page 23). 2. Remove the server blade (on page 24). 3. Remove the access panel ("Access panel" on page 25). 4. Remove the SAS controller ("SAS controller" on page 28). 5. Remove all DIMM baffles ("DIMM baffles" on page 29). 6. Locate the DIMM tool ("Tool locations" on page 77) and remove it from the DIMM baffle. 7. Remove the DIMM and then use the DIMM tool to close the DIMM slot. To replace the component: 1. Use the DIMM tool to open the DIMM slot. Removal and replacement procedures 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
Removal and replacement procedures
31
DIMMs
IMPORTANT:
This server blade does not support mixing LRDIMMs, RDIMMs, or UDIMMs.
Attempting to mix any combination of these DIMMs can cause the server to halt during BIOS
initialization.
To identify the DIMMs installed in the server blade, see "DIMM identification (on page
76
)."
To remove the component:
1.
Power down the server blade (on page
23
).
2.
Remove the server blade (on page
24
).
3.
Remove the access panel ("
Access panel
" on page
25
).
4.
Remove the SAS controller ("
SAS controller
" on page
28
).
5.
Remove all DIMM baffles ("
DIMM baffles
" on page
29
).
6.
Locate the DIMM tool ("
Tool locations
" on page
77
) and remove it from the DIMM baffle.
7.
Remove the DIMM and then use the DIMM tool to close the DIMM slot.
To replace the component:
1.
Use the DIMM tool to open the DIMM slot.