HP ProLiant BL420c HP ProLiant BL420c Gen8 Server Blade Maintenance and Servic - Page 60

Serial label pull tab

Get HP ProLiant BL420c PDF manuals and user guides View all HP ProLiant BL420c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

12. Install the hard drives ("Drive" on page 26). 13. Install the hard drive blanks ("Drive blank" on page 26). 14. Install the access panel ("Access panel" on page 25). Serial label pull tab To remove the component: 1. Power down the server blade (on page 23). 2. Remove the server blade (on page 24). 3. Remove the access panel ("Access panel" on page 25). 4. Remove all hard drives ("Drive" on page 26). 5. Remove all hard drive blanks ("Drive blank" on page 26). 6. Disconnect the capacitor pack cabling, if connected ("FBWC capacitor pack cabling" on page 67). 7. Remove the SAS controller ("SAS controller" on page 28). 8. Remove all DIMM baffles ("DIMM baffles" on page 29). 9. Remove all DIMMs ("DIMMs" on page 31). 10. Remove the heatsink blank, if installed ("Heatsink blank" on page 32). 11. Remove the front panel/hard drive cage assembly ("Front panel/drive cage assembly" on page 43). 12. While holding the system board in place, turn the base pan on its side and remove the two system board screws from the bottom of the base pan. 13. Place the server blade on a flat, level surface. Removal and replacement procedures 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
Removal and replacement procedures
60
12.
Install the hard drives ("
Drive
" on page
26
).
13.
Install the hard drive blanks ("
Drive blank
" on page
26
).
14.
Install the access panel ("
Access panel
" on page
25
).
Serial label pull tab
To remove the component:
1.
Power down the server blade (on page
23
).
2.
Remove the server blade (on page
24
).
3.
Remove the access panel ("
Access panel
" on page
25
).
4.
Remove all hard drives ("
Drive
" on page
26
).
5.
Remove all hard drive blanks ("
Drive blank
" on page
26
).
6.
Disconnect the capacitor pack cabling, if connected ("
FBWC capacitor pack cabling
" on page
67
).
7.
Remove the SAS controller ("
SAS controller
" on page
28
).
8.
Remove all DIMM baffles ("
DIMM baffles
" on page
29
).
9.
Remove all DIMMs ("
DIMMs
" on page
31
).
10.
Remove the heatsink blank, if installed ("
Heatsink blank
" on page
32
).
11.
Remove the front panel/hard drive cage assembly ("
Front panel/drive cage assembly
" on page
43
).
12.
While holding the system board in place, turn the base pan on its side and remove the two system
board screws from the bottom of the base pan.
13.
Place the server blade on a flat, level surface.