HP ProLiant ML310e HP ProLiant ML310e Gen8 Server Maintenance and Service Guid - Page 50

Rear system fan, Dedicated iLO management port

Get HP ProLiant ML310e PDF manuals and user guides View all HP ProLiant ML310e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Rear system fan To remove the component: 1. Power down the server (on page 27). 2. Remove all power: a. Disconnect each power cord from the power source. b. Disconnect each power cord from the server. 3. Unlock the tower bezel (on page 26). 4. Remove the access panel ("Access panel" on page 31). 5. Remove the air baffle ("Air baffle" on page 32). 6. Remove any existing expansion board that blocks access to the rear system fan connector. 7. Disconnect the fan cable. 8. Press and hold the fan latch, and then remove the fan. To replace the component, reverse the removal procedure. Dedicated iLO management port To remove the component: 1. Power down the server (on page 27). 2. Remove all power: a. Disconnect each power cord from the power source. b. Disconnect each power cord from the server. 3. Unlock the tower bezel (on page 26). 4. Remove the access panel ("Access panel" on page 31). 5. Remove the air baffle ("Air baffle" on page 32). 6. Remove the rear system fan ("Rear system fan" on page 50). Removal and replacement procedures 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
Removal and replacement procedures
50
Rear system fan
To remove the component:
1.
Power down the server (on page
27
).
2.
Remove all power:
a.
Disconnect each power cord from the power source.
b.
Disconnect each power cord from the server.
3.
Unlock the tower bezel (on page
26
).
4.
Remove the access panel ("
Access panel
" on page
31
).
5.
Remove the air baffle ("
Air baffle
" on page
32
).
6.
Remove any existing expansion board that blocks access to the rear system fan connector.
7.
Disconnect the fan cable.
8.
Press and hold the fan latch, and then remove the fan.
To replace the component, reverse the removal procedure.
Dedicated iLO management port
To remove the component:
1.
Power down the server (on page
27
).
2.
Remove all power:
a.
Disconnect each power cord from the power source.
b.
Disconnect each power cord from the server.
3.
Unlock the tower bezel (on page
26
).
4.
Remove the access panel ("
Access panel
" on page
31
).
5.
Remove the air baffle ("
Air baffle
" on page
32
).
6.
Remove the rear system fan ("
Rear system fan
" on page
50
).