HP ProLiant ML310e HP ProLiant ML310e Gen8 Server Maintenance and Service Guid - Page 54

System board

Get HP ProLiant ML310e PDF manuals and user guides View all HP ProLiant ML310e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

11. Remove the power supply cage. To replace the component, reverse the removal procedure. System board CAUTION: To avoid ESD damage, when removing electrostatic-sensitive components from the failed system board, place the components on a static-dissipating work surface or inside separate antistatic bags. To remove the system board: 1. Power down the server (on page 27). 2. Remove all power: a. Disconnect each power cord from the power source. b. Disconnect each power cord from the server. 3. Unlock the tower bezel (on page 26). 4. Remove the access panel ("Access panel" on page 31). 5. Remove the air baffle ("Air baffle" on page 32). 6. Remove the rear system fan ("Rear system fan" on page 50). 7. Remove the capacitor pack ("Capacitor pack" on page 46). 8. Remove the heatsink: a. Loosen one pair of diagonally opposite screws halfway, and then loosen the other pair of screws. b. Completely loosen all screws in the same sequence. Removal and replacement procedures 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
Removal and replacement procedures
54
11.
Remove the power supply cage.
To replace the component, reverse the removal procedure.
System board
CAUTION:
To avoid ESD damage, when removing electrostatic-sensitive components from the
failed system board, place the components on a static-dissipating work surface or inside separate
antistatic bags.
To remove the system board:
1.
Power down the server (on page
27
).
2.
Remove all power:
a.
Disconnect each power cord from the power source.
b.
Disconnect each power cord from the server.
3.
Unlock the tower bezel (on page
26
).
4.
Remove the access panel ("
Access panel
" on page
31
).
5.
Remove the air baffle ("
Air baffle
" on page
32
).
6.
Remove the rear system fan ("
Rear system fan
" on page
50
).
7.
Remove the capacitor pack ("
Capacitor pack
" on page
46
).
8.
Remove the heatsink:
a.
Loosen one pair of diagonally opposite screws halfway, and then loosen the other pair of screws.
b.
Completely loosen all screws in the same sequence.