HP ProLiant ML310e HP ProLiant ML310e Gen8 Server Maintenance and Service Guid - Page 52

RPS backplane module

Get HP ProLiant ML310e PDF manuals and user guides View all HP ProLiant ML310e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

WARNING: To reduce the risk of personal injury from hot surfaces, allow the power supply or power supply blank to cool before touching it. 5. Disconnect the power supply cables from the drive cage and the system board. 6. Remove the power supply. To replace the component, reverse the removal procedure. RPS backplane module To remove the component: 1. Power down the server (on page 27). 2. Remove all power: a. Disconnect each power cord from the power source. b. Disconnect each power cord from the server. 3. Unlock and open the tower bezel ("Unlock the tower bezel" on page 26). 4. Remove the access panel ("Access panel" on page 31). 5. Remove the EMI shield from the lower media bay. 6. Remove the optical drive from the upper media bay ("Optical drive" on page 32). 7. Disconnect the power supply cables from the drive cage and the system board. Removal and replacement procedures 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
Removal and replacement procedures
52
WARNING:
To reduce the risk of personal injury from hot surfaces, allow the power supply or
power supply blank to cool before touching it.
5.
Disconnect the power supply cables from the drive cage and the system board.
6.
Remove the power supply.
To replace the component, reverse the removal procedure.
RPS backplane module
To remove the component:
1.
Power down the server (on page
27
).
2.
Remove all power:
a.
Disconnect each power cord from the power source.
b.
Disconnect each power cord from the server.
3.
Unlock and open the tower bezel ("
Unlock the tower bezel
" on page
26
).
4.
Remove the access panel ("
Access panel
" on page
31
).
5.
Remove the EMI shield from the lower media bay.
6.
Remove the optical drive from the upper media bay ("
Optical drive
" on page
32
).
7.
Disconnect the power supply cables from the drive cage and the system board.