Home » HP Manuals » Storage Devices » HP StorageWorks 2/64 » Manual Viewer

HP StorageWorks 2/64 HP StorageWorks Fabric OS 5.x Fabric Watch Administrator - Page 44

Option, Effect, Input information

View all HP StorageWorks 2/64 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Table 15 describes the 18 customization options displayed at the end of the Advanced Configuration menu. Table 15 Advanced configuration options Option Effect Input information change behavior type Changes the behavior type of a single element to either Triggered or Continuous. The change is volatile because this option is not saved to flash memory. Every time the switch is rebooted, this option is reset. The element index and the required behavior type change behavior interval Changes the behavior interval for a single element. The change is volatile because this option is not saved to flash memory. Every time the switch is rebooted, this option is reset. The element index and the required behavior interval, in seconds change threshold boundary level Changes between the factory The required threshold column default and custom threshold information. change custom unit Changes the measurement unit assigned to the monitored data values, but only affects the custom column. The required measurement unit, as a string change custom time base Changes the time base for the The required time base area, but only affects the custom column. change custom low Changes the low setting for the threshold, but only affects the custom column. The required low threshold, in the units defined by the area change custom high Changes the high setting for the threshold, but only affects the custom column. The required high threshold, in the units defined by the area change custom buffer Changes the buffer size for the The required buffer size, in the threshold, but only affects the units defined by the area custom column. apply threshold boundary changes Confirms the changes made to the threshold information. This must be done to retain the changes made. None cancel threshold boundary changes Returns the boundary information to the last confirmed state. None change threshold alarm level Changes between the factory The required event setting column default and custom event settings for the area. 44 Configuring Fabric Watch

Section	Page
Contents	3
Intended audience	7
Related documentation	7
Document conventions and symbols	8
Table 1 Document conventions	8
HP technical support	9
HP-authorized reseller	9
Helpful web sites	9
An introduction to Fabric Watch	11
Fabric Watch overview	11
Introduction to fabric health	12
Fabric Watch concepts	13
Fabric watch components	13
Classes	13
Table 2 Fabric Watch classes	13
Areas	14
Environment class areas	14
Table 3 Environment class areas	14
Fabric class areas	15
Table 4 Fabric class sreas	15
FRU class areas	15
Table 5 FRU class areas	15
Performance monitor class areas	16
Table 6 Performance monitor class areas	16
Port class areas	16
Table 7 Port class areas	16
Resource class area	17
Table 8 Resource class area	17
Security class areas	17
Table 9 Security class areas	17
SFP class areas	18
Table 10 SFP class areas	18
Elements	19
Configuring events	19
Event behavior types	19
Continuous event behavior	19
Triggered event behavior	20
Data values	20
Threshold values	20
High and low thresholds	20
Buffer values	20
Figure 1 Threshold monitoring	21
Figure 2 A buffered data region	21
Time bases	21
Setting time base to none	21
Figure 3 Time base set to none	21
Specifying a time base	22
Figure 4 Event trigger	22
Figure 5 Example without an event	23
Event settings	23
Above event triggers	23
Figure 6 Above event trigger with buffer zone	23
Below event trigger	24
Changed event trigger	24
Figure 7 Changed threshold	24
In-Between triggers	24
Figure 8 In-Between trigger	24
Port persistence	25
Notification methods	25
Switch event (error) log entry	25
SNMP trap	25
RAPITrap	26
Port log lock	26
Email alert	26
Assigning notification methods	26
Table 11 Numerical values of notification methods	26
Switch policies	27
Interpreting event messages	27
Activating and accessing Fabric Watch	29
Activating Fabric Watch	29
Activating with telnet	29
Activating with Advanced Web Tools	29
Accessing Fabric Watch	29
Telnet	30
Advanced Web Tools	30
SNMP-Based enterprise managers	30
Configuration file	32
Configuring Fabric Watch	33
Configuring Fabric Watch thresholds	33
Step 1: Select the class and area to configure	33
Table 12 Element listing information - RXPerformance area menu	34
Step 2: Configure thresholds	35
1. refresh	35
2. disable a threshold	35
Figure 9 Disabling a threshold	36
3. enable a threshold	36
4. advanced configuration	37
Table 13 Element listing information - Advanced Configuration Menu	38
Table 14 Element listing information - threshold boundary menu	40
Step 3: Configure alarms	41
How to calculate values for alarms	41
Figure 10 Changing the threshold alarm level	43
Figure 11 Applying threshold alarm changes	43
Table 15 Advanced configuration options	44
Step 4: Disable and enable thresholds by port (optional)	45
Configuring notifications	46
Configuring alarm notifications	46
Configuring SNMP notifications	46
Configuring port log lock actions	46
Configuring email notifications	47
Figure 12 fwMailcfg Menu	47
1: Show Mail configuration information	47
Figure 13 Config show menu	47
Configuring switch status policy	49
Step 1: Plan and define your switch status policy	49
Table 16 Switch status policy monitor health factors	49
Step 2: Implement your switch status policy	50
Step 3: View your switch status policy	50
Configuring FRUs	50
Figure 14 fwFruCfg configuration	51
Configuring Fabric Watch using Web Tools	51
Configuring Fabric Watch using SNMP	51
Figure 15 Configuring Fabric Watch using SNMP	52
Figure 16 Enabling Fabric Watch Traps in SNMP	52
Figure 17 Configuring SNMP management host IP address	53
Figure 18 Example OID tree	54
Figure 19 Example swFwName screen	54
Default threshold values	57
Environment class	57
Table 17 Environment class threshold defaults	58
Fabric class	60
Table 18 Fabric Class threshold defaults	60
Performance monitor class	61
Table 19 AL_PA performance monitor class threshold defaults	61
Table 20 Customer-Defined performance monitor class threshold defaults	61
Table 21 End-to-End performance monitor class threshold defaults	62
Port class	62
Table 22 Port Class threshold defaults	62
Table 23 E-Port class threshold defaults	63
Table 24 F/FL-Port class threshold defaults	64
Resource class	65
Table 25 Resource class threshold defaults	65
Security class	66
Table 26 Security class threshold defaults	66
SFP class	68
Table 27 SFP Class Threshold Defaults	68
Basic Fabric Watch configuration guidelines	69
Using Fabric Watch with configuration files	71
Configuration files	71

Match case Limit results 1 per page

Configuring Fabric Watch

Table 15

describes the 18 customization options displayed at the end of the Advanced Configuration

menu.

Table 15

Advanced configuration options

Option

Effect

Input information

change behavior type

Changes the behavior type of

a single element to either

Triggered or Continuous. The

change is volatile because this

option is not saved to flash

memory. Every time the switch

is rebooted, this option is

reset.

The element index and the

required behavior type

change behavior interval

Changes the behavior interval

for a single element. The

change is volatile because this

option is not saved to flash

memory. Every time the switch

is rebooted, this option is

reset.

The element index and the

required behavior interval, in

seconds

change threshold

boundary level

Changes between the factory

default and custom threshold

information.

The required threshold column

change custom unit

Changes the measurement

unit assigned to the monitored

data values, but only affects

the custom column.

The required measurement unit,

as a string

change custom time base

Changes the time base for the

area, but only affects the

custom column.

The required time base

change custom low

Changes the low setting for

the threshold, but only affects

the custom column.

The required low threshold, in the

units defined by the area

change custom high

Changes the high setting for

the threshold, but only affects

the custom column.

The required high threshold, in

the units defined by the area

change custom buffer

Changes the buffer size for the

threshold, but only affects the

custom column.

The required buffer size, in the

units defined by the area

apply threshold boundary

changes

Confirms the changes made to

the threshold information. This

must be done to retain the

changes made.

None

cancel threshold

boundary changes

Returns the boundary

information to the last

confirmed state.

None

change threshold alarm

level

Changes between the factory

default and custom event

settings for the area.

The required event setting column