HP StorageWorks 2000sa HP StorageWorks P2000 G3 MSA System Event Description R - Page 12

Warning, Informational, Error

Get HP StorageWorks 2000sa - G2 Modular Smart Array PDF manuals and user guides View all HP StorageWorks 2000sa manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

89 Warning The mirrored configuration retrieved by this controller from the partner controller has a configuration level that is too high for the firmware in this controller to process. The local flash configuration will be used instead. Recommended actions • The current controller probably has down-level firmware. Update the firmware on the down-level controller. Both controllers should have the same firmware versions. When the problem is fixed, event 20 is logged. 90 Informational The partner controller does not have a mirrored configuration image for the current controller, so the current controller's local flash configuration is being used. This event is expected if the other controller is new or its configuration has been changed. Recommended actions • No action required. 91 Error In a testing environment, the diagnostic that checks hardware reset signals between controllers in Active-Active mode failed. Recommended actions • Perform failure analysis. 95 Error Both controllers in an Active-Active configuration have the same serial number. Non-unique serial numbers can cause system problems; for example, vdisk ownership and WWNs are determined by serial number. Recommended actions • Replace one of the controller modules. 96 Informational Pending configuration changes that take effect at startup were ignored because customer data might be present in cache. Recommended actions • If the requested configuration changes did not occur, make the changes again and then use a user-interface command to shut down or restart the controller. 100 Informational During Active-Active operation, an event (potential error) occurred while communicating with the enclosure management processor (EMP). Recommended actions • No action required. 101 Informational An update of enclosure management processor (EMP) data has been triggered. Recommended actions • No action required. 103 Informational The name has been changed for the indicated volume. Recommended actions • No action required. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
12
89
Warning
The mirrored configuration retrieved by this controller from the partner controller has a configuration level
that is too high for the firmware in this controller to process. The local flash configuration will be used
instead.
Recommended actions
•
The current controller probably has down-level firmware. Update the firmware on the down-level
controller. Both controllers should have the same firmware versions.
When the problem is fixed, event 20 is logged.
90
Informational
The partner controller does not have a mirrored configuration image for the current controller, so the current
controller’s local flash configuration is being used. This event is expected if the other controller is new or its
configuration has been changed.
Recommended actions
•
No action required.
91
Error
In a testing environment, the diagnostic that checks hardware reset signals between controllers in
Active-Active mode failed.
Recommended actions
•
Perform failure analysis.
95
Error
Both controllers in an Active-Active configuration have the same serial number. Non-unique serial numbers
can cause system problems; for example, vdisk ownership and WWNs are determined by serial number.
Recommended actions
•
Replace one of the controller modules.
96
Informational
Pending configuration changes that take effect at startup were ignored because customer data might be
present in cache.
Recommended actions
•
If the requested configuration changes did not occur, make the changes again and then use a
user-interface command to shut down or restart the controller.
100
Informational
During Active-Active operation, an event (potential error) occurred while communicating with the enclosure
management processor (EMP).
Recommended actions
•
No action required.
101
Informational
An update of enclosure management processor (EMP) data has been triggered.
Recommended actions
•
No action required.
103
Informational
The name has been changed for the indicated volume.
Recommended actions
•
No action required.