Home » Hitachi Manuals » Hard Drives » Hitachi 7K100 » Manual Viewer

Hitachi 7K100 Hard Drive Specifications - Page 139

General Purpose Log Directory

UPC - 683728198671

Add to My Manuals
Save this manual to your list of manuals

Page 139 highlights

Table 82: Log Address Definition Log Address 00h 03h 06h 07h 20h 21h 22h 80h-9Fh Content Feature set Log directory N/A Extended Comprehensive SMART error log SMART error logging SMART self-test log SMART self-test Extended SMART self-test log SMART self-test Streaming Performance log Streaming Write Stream Error log Streaming Read Stream Error log Streaming Host vendor specific SMART Type Read Only Ready Only See Note Read Only Read Only Read Only Read Only Read/Write Note: If log address 06h is accessed using the Read Log Ext or Write Log Ext commands, command abort shall be returned. The Extended SMART self-test log sector shall support 48-bit and 28-bit addressing. All 28-bit entries contained in the SMART self-test log sector shall also be included in the Comprehensive SMART self-test log sector with the 48-bit entries. If the feature set associated with the log specified in the Sector Number register is not supported or enabled, or if the values in the Sector Count, Sector Number or Cylinder Low registers are invalid, the device shall return command aborted. 13.15.1 General Purpose Log Directory The figure below defines the 512 bytes that make up the General Purpose Log Directory. Table 83: General Purpose Log Directory Description General purpose logging version Number of sectors in the log at log address 01h (7:0) Number of sectors in the log at log address 01h (15:8) Number of sectors in the log at log address 01h (7:0) Number of sectors in the log at log address 01h (15:8) ... Number of sectors in the log at log address 20h (7:0) Number of sectors in the log at log address 20h (7:0) Number of sectors in the log at log address 21h (7:0) Number of sectors in the log at log address 22h (7:0) Number of sectors in the log at log address 22h (15:8) Bytes 2 1 1 1 1 1 1 1 1 1 Offset 00h 02h 03h 04h 05h 40h 41h 42h 44h 45h Number of sectors in the log at address 80h (7:0) Number of sectors in the log at address 80h (15:8) 1 100h 1 101h Number of sectors in the log at address FFh (7:0) Number of sectors in the log at address FFh (15:8) 1 1FEh 1 1FFh 512 Travelstar 7K100 Hard Disk Drive Specification 125

Section	Page
1.0 General	15
1.1 Introduction	15
1.2 References	15
1.3 Abbreviations	15
1.4 Caution	17
1.5 Drive handling precautions	17
2.0 Outline of the drive	19
3.0 Fixed-disk subsystem description	23
3.1 Control electronics	23
3.2 Head disk assembly data	23
4.0 Drive characteristics	25
4.1 Formatted capacity	25
4.2 Data sheet	25
4.3 Cylinder allocation	26
4.4 Performance characteristics	27
4.4.1 Command overhead	27
4.4.2 Mechanical positioning	28
4.4.3 Operating modes	30
5.0 Data integrity	31
5.1 Data loss at power off	31
5.2 Write Cache	31
5.3 Equipment status	31
5.4 WRITE safety	32
5.5 Data buffer test	32
5.6 Error recovery	32
5.7 Automatic reallocation	32
5.8 ECC	33
6.0 Specification	35
6.1 Environment	35
6.1.1 Temperature and humidity	35
6.1.2 Radiation noise	37
6.1.3 Conductive noise	37
6.1.4 Magnetic fields	37
6.2 DC power requirements	38
6.2.1 Power consumption efficiency	38
6.3 Reliability	39
6.3.1 Data Reliability	39
6.3.2 Failure prediction (S.M.A.R.T.)	39
6.3.3 Cable noise interference	39
6.3.4 Service life and usage condition	39
6.3.5 Preventive maintenance	39
6.3.6 Load/unload	40
6.4 Mechanical specifications	42
6.4.1 Physical dimensions and weight	42
6.4.2 Mounting hole locations	42
6.4.3 Connector and jumper description	42
6.4.4 Mounting orientation	43
6.4.5 Load/unload mechanism	43
6.5 Vibration and shock	44
6.5.1 Operating vibration	44
6.5.2 Nonoperating vibration	45
6.5.3 Operating shock	45
6.5.4 Nonoperating shock	45
6.6 Acoustics	46
6.6.1 Sound power levels	46
6.6.2 Discrete tone penalty	46
6.7 Identification labels	47
6.8 Electromagnetic compatibility	47
6.8.1 CE mark	47
6.8.2 C-TICK mark	47
6.8.3 BSMI mark	47
6.8.4 MIC mark	47
6.9 Safety	48
6.9.1 UL and CSA approval	48
6.9.2 IEC compliance	48
6.9.3 German safety mark	48
6.9.4 Flammability	48
6.9.5 Secondary circuit protection	48
6.10 Packaging	48
7.0 Electrical interface specification	49
7.1 Cabling	49
7.2 Interface connector	49
7.3 Signal definitions	50
7.4 Signal descriptions	51
7.5 Interface logic signal levels	54
7.6 Reset timings	54
7.7 PIO timings	55
7.8 Multi word DMA timings	56
7.9 Ultra DMA timings	57
7.9.1 Initiating Read DMA	57
7.9.2 Host Pausing Read DMA	58
7.9.3 Host Terminating Read DMA	59
7.9.4 Device Terminating Read DMA	60
7.9.5 Initiating Write DMA	61
7.9.6 Device Pausing Write DMA	62
7.9.7 Device Terminating Write DMA	63
7.9.8 Host Terminating Write DMA	64
7.10 Drive address setting	65
7.11 Addressing of HDD registers	66
8.0 General	69
8.1 Introduction	69
8.2 Terminology	69
9.0 Deviations from standard	71
10.0 Register	73
10.1 Alternate Status Register	74
10.2 Command Register	74
10.3 Data Register	74
10.4 Device Control Register	75
10.5 Drive Address Register	75
10.6 Device Register	76
10.7 Error Register	76
10.8 Features Register	77
10.9 LBA High Register	77
10.10 LBA Low Register	77
10.11 LBA Mid Register	77
10.12 Sector Count Register	77
10.13 Status Register	78
11.0 General	79
11.1 Reset response	79
11.2 Register initialization	80
11.3 Diagnostic and Reset considerations	81
11.4 Power-off considerations	82
11.4.1 Load/Unload	82
11.4.2 Emergency unload	82
11.4.3 Required power-off sequence	82
11.5 Sector Addressing Mode	83
11.5.1 Logical CHS addressing mode	83
11.5.2 LBA addressing mode	83
11.6 Power management features	84
11.6.1 Power mode	84
11.6.2 Power management commands	84
11.6.3 Standby/Sleep command completion time	84
11.6.4 Standby timer	85
11.6.5 Status	85
11.6.6 Interface capability for power modes	85
11.6.7 Initial Power Mode at Power On	85
11.7 Advanced Power Management (ABLE-3) feature	85
11.7.1 Performance Idle Mode	86
11.7.2 Active Idle Mode	86
11.7.3 Low Power Idle Mode	86
11.7.4 Transition time	86
11.8 S.M.A.R.T. Function	87
11.8.1 Attributes	87
11.8.2 Attribute values	87
11.8.3 Attribute thresholds	87
11.8.4 Threshold exceeded condition	87
11.8.5 S.M.A.R.T. commands	87
11.8.6 S.M.A.R.T. operation with power management modes	88
11.9 Security Mode Feature Set	88
11.9.1 Security mode	88
11.9.2 Security level	88
11.9.3 Password	89
11.9.4 Master Password Revision Code	89
11.9.5 Command table	92
11.10 Protected Area Function	93
11.10.1 Example for operation (In LBA Mode)	93
11.10.2 Set Max security extension commands	94
11.11 Address Offset Feature (vendor specific)	95
11.11.1 Enable/Disable Address Offset Mode	95
11.11.2 Identify Device Data	96
11.11.3 Exceptions in Address Offset Mode	96
11.12 Seek Overlap	97
11.13 Write Cache function	97
11.14 Reassign Function	98
11.14.1 Auto Reassign Function	98
11.15 48-bit Address Feature Set	99
12.0 Command protocol	101
12.1 Data In commands	101
12.2 Data Out Commands	102
12.3 Non-data commands	103
12.4 DMA Data Transfer commands:	105
13.0 Command descriptions	107
13.1 Check Power Mode (E5h/98h)	112
13.2 Device Configuration Overlay (B1h)	113
13.2.1 DEVICE CONFIGURATION RESTORE (subcommand C0h)	113
13.2.2 DEVICE CONFIGURATION FREEZE LOCK (subcommand C1h)	113
13.2.3 DEVICE CONFIGURATION IDENTIFY (subcommand C2h)	114
13.2.4 DEVICE CONFIGURATION SET (subcommand C3h)	114
13.3 Execute Device Diagnostic (90h)	116
13.4 Flush Cache (E7h)	117
13.5 Flush Cache EXT (EAh)	118
13.6 Format Track (50h: vendor specific)	119
13.7 Format Unit (F7h: vendor specific)	120
13.8 Identify Device (ECh)	121
13.9 Idle (E3h/97h)	130
13.10 Idle Immediate (E1h/95h)	131
13.11 Initialize Device Parameters (91h)	132
13.12 Read Buffer (E4h)	133
13.13 Read DMA (C8h/C9h)	134
13.14 Read DMA EXT (25h)	136
13.15 Read Log Ext (2Fh)	138
13.15.1 General Purpose Log Directory	139
13.15.2 Extended Comprehensive SMART Error Log	140
13.15.3 Extended Self-test log sector	142
13.16 Read Long (22h/23h)	144
13.17 Read Multiple (C4h)	146
13.18 Read Multiple EXT (29h)	148
13.19 Read Native Max ADDRESS (F8h)	149
13.20 Read Native Max ADDRESS EXT (27h)	150
13.21 Read Sectors (20h/21h)	151
13.22 Read Sector(s) EXT (24h)	152
13.23 Read Verify Sectors (40h/41h)	154
13.24 Ready Verify Sector(s) EXT (42h)	156
13.25 Recalibrate (1xh)	158
13.26 Security Disable Password (F6h)	159
13.27 Security Erase Prepare (F3h)	160
13.28 Security Erase Unit (F4h)	161
13.29 Security Freeze Lock (F5h)	163
13.30 Security Set Password (F1h)	164
13.31 Security Unlock (F2h)	166
13.32 Seek (7xh)	167
13.33 Sense Condition (F0h: vendor specific)	168
13.34 Set Features (EFh)	169
13.35 Set Max ADDRESS (F9h)	171
13.36 Set Max ADDRESS EXT (37h)	173
13.37 Set Multiple (C6h)	175
13.38 Sleep (E6h/99h)	176
13.39 S.M.A.R.T. Function Set (B0h)	177
13.39.1 S.M.A.R.T. Function Subcommands	178
13.39.2 Device Attribute Data Structure	183
13.39.3 Device Attribute Thresholds data structure	188
13.39.4 S.M.A.R.T. Log Directory	190
13.39.5 S.M.A.R.T. error log sector	190
13.39.6 Self-test log data structure	193
13.39.7 Selective self-test log data structure	193
13.39.8 Error reporting	194
13.40 Standby (E2h/96h)	195
13.41 Standby Immediate (E0h/94h)	196
13.42 Write Buffer (E8h)	197
13.43 Write DMA (CAh/CBh)	198
13.44 Write DMA EXT (35h)	200
13.45 Write Log Ext (3Fh)	202
13.46 Write Long (32h/33h)	203
13.47 Write Multiple (C5h)	205
13.48 Write Multiple EXT (39h)	206
13.49 Write Sectors (30h/31h)	208
13.50 Write Sectors(s) EXT (34h)	210
13.51 Write Verify (3Ch: vendor specific)	211
14.0 Time-out values	213
15.0 Appendix	215
15.1 Commands Support Coverage	215
15.2 SET FEATURES Commands Support Coverage	217

Match case Limit results 1 per page

Travelstar 7K100 Hard Disk Drive Specification

125

Table 82: Log Address Definition

Note:

If log address 06h is accessed using the Read Log Ext or Write Log Ext commands, command abort shall be

returned.

The Extended SMART self-test log sector shall support 48-bit and 28-bit addressing. All 28-bit entries contained in

the SMART self-test log sector shall also be included in the Comprehensive SMART self-test log sector with the

48-bit entries.

If the feature set associated with the log specified in the Sector Number register is not supported or enabled, or if

the values in the Sector Count, Sector Number or Cylinder Low registers are invalid, the device shall return com-

mand aborted.

13.15.1

General Purpose Log Directory

The figure below defines the 512 bytes that make up the General Purpose Log Directory.

Table 83: General Purpose Log Directory

Log Address

Content

Feature set

Type

00h

Log directory

N/A

Read Only

03h

Extended Comprehensive SMART error log SMART error logging

Ready Only

06h

SMART self-test log

SMART self-test

See Note

07h

Extended SMART self-test log

SMART self-test

Read Only

20h

Streaming Performance log

Streaming

Read Only

21h

Write Stream Error log

Streaming

Read Only

22h

Read Stream Error log

Streaming

Read Only

80h-9Fh

Host vendor specific

SMART

Read/Write

Description

Bytes

Offset

General purpose logging version

00h

Number of sectors in the log at log address 01h (7:0)

02h

Number of sectors in the log at log address 01h (15:8)

03h

Number of sectors in the log at log address 01h (7:0)

04h

Number of sectors in the log at log address 01h (15:8)

05h

...

Number of sectors in the log at log address 20h (7:0)

40h

Number of sectors in the log at log address 20h (7:0)

41h

Number of sectors in the log at log address 21h (7:0)

42h

Number of sectors in the log at log address 22h (7:0)

44h

Number of sectors in the log at log address 22h (15:8)

45h

Number of sectors in the log at address 80h (7:0)

100h

Number of sectors in the log at address 80h (15:8)

101h

Number of sectors in the log at address FFh (7:0)

1FEh

Number of sectors in the log at address FFh (15:8)

1FFh

512