Hitachi DV-S522U Owners Guide - Page 38

Maintenance

Get Hitachi DV-S522U PDF manuals and user guides View all Hitachi DV-S522U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

To release the timer 1. After turning the power on, press [TIMER] while holding [SHIFT] down. 2. Press [SET/CLEAR] while holding [SHIFT] down. Note: • If [SET/CLEAR] is pressed while holding [SHIFT] down, while the timer is being set, the original display returns. • The timer mode is released if a power failure occurs during timer controlled operation. • The timer may not operate if a power failure occurs during timer operation standby mode. Using the Sleep Timer The sleep timer automatically switches off the power after a preset time has elapsed. The volume will gradually be reduced (fade-out) during the 1 minute period before the unit turns off. There are 9 time periods available: 90, 80, 70, 60, 50, 40, 30, 20, and 10 minutes. Press [SLEEP] repeatedly while holding [SHIFT] down to select the desired sleep time. "SLEEP" appears on the display. After several seconds, the original display returns and the brightness of the display reduces. To check the remaining sleep time Press [SLEEP] once while holding [SHIFT] down. After several seconds, the original display returns. To release the sleep timer while in operation Press [SLEEP] repeatedly while holding [SHIFT] down until "SLEEP" disappears. The timer is also released if the power is switched off. z/ I SHIFT LAST MEMO REPEAT DISPLAY SEARCH MODE RETURN PROG TV POWER TV CH TV/VIDEO TV CH TV VOL TV VOL UP ME SET ITLE NU TOP M SHIFT REV SLOW ENTER ENU SUBT CLEAR TRIM FWD SLOW -TUNE PREV PAUSE/STEP NEXT TUNE+ TIMER 1 ANGLE 4 7 TIMER 0 CLOCK 2 A.REPLAY 5 AUDIO 8 ADJUST 3 ZOOM 6 SLEEP 9 SET/CLEAR +10 SET/CLEAR SHIFT UP ME SET ITLE NU TOP M SHIFT REV SLOW ENTER ENU SUBT CLEAR TRIM FWD SLOW -TUNE PREV PAUSE/STEP NEXT TUNE+ 1 ANGLE 4 7 TIMER 0 CLOCK 2 A.REPLAY 5 AUDIO 8 ADJUST 3 ZOOM 6 SLEEP 9 SET/CLEAR +10 SLEEP MAINTENANCE WARNING: FOR YOUR PERSONAL SAFETY, BE SURE TO DISCONNECT THE AC POWER CORD BEFORE PROCEEDING WITH ANY MAINTENANCE OR CLEANING. Cleaning the cabinet Use a clean soft cloth moistened with plain lukewarm water and wrung dry. Never use benzol, benzene or other strong chemical cleaners since these could damage the finish of your unit. It is important that no liquid reaches the inside of the unit. -E37-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
-E37-
P
A
U
S
E
/
S
T
E
P
P
R
E
V
N
E
X
T
-
T
U
N
E
T
U
N
E
+
REV
SLOW
FWD
SLOW
CLEAR
TRIM
RETURN
DISPLAY
PROG
TV CH
TV VOL
TV VOL
TV CH
TV/VIDEO
LAST MEMO
REPEAT
SEARCH MODE
TV POWER
ENTER
SHIFT
S
E
T
U
P
T
O
P
M
E
N
U
S
U
B
T
I
T
L
E
M
E
N
U
0
8
7
9
+10
5
4
6
2
1
3
ANGLE
A.REPLAY
ZOOM
AUDIO
SLEEP
TIMER
ADJUST
SET/CLEAR
CLOCK
SHIFT
SET/CLEAR
TIMER
z
/ I
P
A
U
S
E
/
S
T
E
P
P
R
E
V
N
E
X
T
-
T
U
N
E
T
U
N
E
+
REV
SLOW
FWD
SLOW
CLEAR
TRIM
ENTER
SHIFT
S
E
T
U
P
T
O
P
M
E
N
U
S
U
B
T
I
T
L
E
M
E
N
U
0
8
7
9
+10
5
4
6
2
1
3
ANGLE
A.REPLAY
ZOOM
AUDIO
SLEEP
TIMER
ADJUST
SET/CLEAR
CLOCK
SHIFT
SLEEP
MAINTENANCE
WARNING:
FOR YOUR PERSONAL SAFETY, BE SURE TO
DISCONNECT THE AC POWER CORD BEFORE
PROCEEDING WITH ANY MAINTENANCE OR CLEANING.
Cleaning the cabinet
Use a clean soft cloth moistened with plain lukewarm water and
wrung dry. Never use benzol, benzene or other strong chemical
cleaners since these could damage the finish of your unit. It is
important that no liquid reaches the inside of the unit.
To release the timer
1.
After turning the power on, press [TIMER] while holding
[SHIFT] down.
2.
Press [SET/CLEAR] while holding [SHIFT] down.
Note:
•
If [SET/CLEAR] is pressed while holding [SHIFT] down, while
the timer is being set, the original display returns.
•
The timer mode is released if a power failure occurs during
timer controlled operation.
•
The timer may not operate if a power failure occurs during
timer operation standby mode.
Using the Sleep Timer
The sleep timer automatically switches off the power after a
preset time has elapsed. The volume will gradually be reduced
(fade-out) during the 1 minute period before the unit turns off.
There are 9 time periods available: 90, 80, 70, 60, 50, 40, 30, 20,
and 10 minutes.
Press [SLEEP] repeatedly while holding [SHIFT] down to select
the desired sleep time. “SLEEP” appears on the display.
After several seconds, the original display returns and the
brightness of the display reduces.
To check the remaining sleep time
Press [SLEEP] once while holding [SHIFT] down.
After several seconds, the original display returns.
To release the sleep timer while in operation
Press [SLEEP] repeatedly while holding [SHIFT] down until
“SLEEP” disappears.
The timer is also released if the power is switched off.