Hitachi NR90GC Service Manual - Page 66

and Internal Wire

Get Hitachi NR90GC - 3-1/2inch Gas Powered Clipped Head Framing Nailer PDF manuals and user guides
UPC - 717709008533
View all Hitachi NR90GC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

(b) Reassembly Reassembly procedures should be followed in the reverse order. Note the following points. Be careful of the split direction of the Roll Pin D2.5 x 10 [99] when mounting the Trigger [98] and Internal Wire (A) [86]. Do not damage the plunger of the switch (Fig. 55). Perform wiring of the Controller [101] and Internal Wire (A) [86] as shown in Fig. 56. Position the other parts as shown in Fig. 56. Do not apply tension to the high-voltage cable of the Controller [101] and the connector of Internal Wire (A) [86] (Fig. 56). Mount the Wiring Cover [103] to Handle (B) [84] then hang the Chamber Lock Bar [100] on the ring of the Lock Bar Spring [102]. Hang the magazine plate on the claw of Handle (B) [84] (3 places) (Fig. 58). Be careful of the mounting direction of the Tension Plate [113] (Fig. 59). Internal Wire (A) [86] Roll Pin D2.5 x 10 [99] Split Plunger Trigger [98] Fig. 55 --- 63 ---

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
--- 63 ---
(b) Reassembly
Reassembly procedures should be followed in the reverse order.
Note the following points.
Be careful of the split direction of the Roll Pin D2.5 x 10
[99]
when mounting the Trigger
[98]
and Internal Wire
(A)
[86]
.
Do not damage the plunger of the switch (Fig. 55).
Perform wiring of the Controller
[101]
and Internal Wire (A)
[86]
as shown in Fig. 56.
Position the other parts
as shown in Fig. 56.
Do not apply tension to the high-voltage cable of the Controller
[101]
and the connector
of Internal Wire (A)
[86]
(Fig. 56).
Mount the Wiring Cover
[103]
to Handle (B)
[84]
then hang the Chamber Lock Bar
[100]
on the ring of the
Lock Bar Spring
[102]
.
Hang the magazine plate on the claw of Handle (B)
[84]
(3 places) (Fig. 58).
Be careful of the mounting direction of the Tension Plate
[113]
(Fig. 59).
Fig. 55
Roll Pin D2.5 x 10
[99]
Plunger
Internal Wire (A)
[86]
Trigger
[98]
Split