Hitachi P50X902 Owners Guide - Page 12

Quick Setup Guide - remote

Get Hitachi P50X902 - 50inch Plasma TV PDF manuals and user guides View all Hitachi P50X902 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Quick Setup Guide Perform the following steps to quickly setup your new Hitachi Plasma Television Set. 1. ANTENNA CONNECTION Unless your Plasma Television is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended for best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient. a). VHF (75-Ohm) antenna/CATV (Cable TV) When using a 75-Ohm coaxial cable system, connect CATV coaxial cable to the AIR/CABLE (75-Ohm) terminal. Or if you have an antenna, connect the coaxial cable to the same AIR/CABLE terminal. To outdoor Antenna or Cable TV (CATV) System To Antenna Terminal b). VHF (300-Ohm) antenna/UHF antenna When using a 300-Ohm twin lead from an outdoor antenna, connect the VHF or UHF antenna leads to screws of the VHF or UHF adapter. Plug the adapter into the antenna terminal on the TV. To outdoor VHF or UHF Antenna To Antenna Terminal Air/Cable Antenna Terminal Rear Panel Jack c). When both VHF and UHF antennas are connected Attach an optional antenna cable mixer to the TV antenna terminal, and connect the cables to the antenna mixer. Consult your dealer or service store for the antenna mixer. To UHF antenna Air/Cable To outdoor antenna or CATV system Antenna Mixer NOTE Connecting a 300-Ohm twin lead connector may cause interference. Using a 75-Ohm coaxial cable is recommended. 2. CONNECT YOUR NEW HITACHI PLASMA TV TO THE POWER SOURCE a). Connect the power cord to your TV set and secure it c). The Indicating Lamp will light Red (Standby mode) and with the cable tie (see page 7) . then light blue (image displays). Indicating Lamp b). Connect the power cord to the AC Wall outlet . 3. POWER ON/OFF YOUR NEW HITACHI PLASMA TV. Press the POWER button on the Remote Control or the POWER switch on the Side Control Panel for power on/off (Stand-By mode). NOTE If the Power Switch is set to OFF, the Power Button on the Remote Control will not operate. or For Stand-By Power OFF 4. FOLLOW THE TV SETUP WIZARD INSTRUCTIONS ON NEXT PAGE. 12 CH CURSOR + VO_L INPUT/ EXIT MENU / SELECT POWER

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
12
Quick Setup Guide
Perform the following steps to quickly setup your new
Hitachi Plasma Television Set.
1. ANTENNA CONNECTION
Unless your Plasma Television is connected to a cable TV system
or to a centralized antenna system, a good outdoor color TV
antenna is recommended for best performance. However, if you
are located in an exceptionally good signal area that is free from
interference and multiple image ghosts, an indoor antenna may be
sufficient.
VHF (75-Ohm) antenna/CATV (Cable TV)
a).
When using a 75-Ohm coaxial cable system, connect CATV
coaxial cable to the AIR/CABLE (75-Ohm) terminal. Or if you have
an antenna, connect the coaxial cable to the same
AIR/CABLE
terminal.
To outdoor Antenna
or
Cable TV (CATV)
System
To Antenna
Terminal
VHF (300-Ohm) antenna/UHF antenna
b).
When using a 300-Ohm twin lead from an outdoor antenna,
connect the VHF or UHF antenna leads to screws of the VHF or
UHF adapter. Plug the adapter into the antenna terminal on the
TV.
To outdoor VHF or
UHF Antenna
To Antenna
Terminal
Connecting a 300-Ohm twin lead connector may cause interference. Using a 75-Ohm coaxial cable is recommended.
NOTE
Rear Panel Jack
Antenna Terminal
Connect the power cord to your TV set and secure it
a).
with the cable tie (see page 7) .
Connect the power cord to the AC Wall outlet .
b).
When both VHF and UHF antennas are connected
c).
Attach an optional antenna cable mixer to the TV antenna terminal,
and connect the cables to the antenna mixer. Consult your dealer
or service store for the antenna mixer.
To outdoor antenna
or CATV system
To UHF antenna
Antenna Mixer
Air/Cable
The Indicating Lamp will light Red (Standby mode) and
c).
then light blue (image displays).
2. CONNECT YOUR NEW HITACHI PLASMA TV TO THE POWER SOURCE
3. POWER ON/OFF YOUR NEW HITACHI PLASMA TV.
Press the POWER button on the Remote Control or the
POWER switch on the Side Control Panel for power on/off
(Stand-By mode).
4. FOLLOW THE TV SETUP WIZARD INSTRUCTIONS ON NEXT PAGE.
or
Air/Cable
POWER
CH
CURSOR
+
_
VOL
INPUT
/
EXIT
MENU
/
SELECT
For Stand-By
Power OFF
Indicating
Lamp
If the Power Switch is set to OFF, the Power Button
on the Remote Control will not operate.
NOTE