Honeywell VISTA 15P Operation Guide - Page 18

On-Board Triggers - installation guide

Get Honeywell VISTA 15P - Ademco 6 Zone Control Panel PDF manuals and user guides
UPC - 781410414846
View all Honeywell VISTA 15P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Installation and Setup Guide On-Board Triggers Connect field wiring to the desired trigger pin on the 8-pin trigger connector centrally located above the terminal strip. • If using 1361X10 transformer and powerline carrier devices, use the SA4120XM-1 cable (part of 4120TR Trigger Cable). See Wiring the AC Transformer section for transformer connections. • If only using the on-board triggers, you can use a 4-wire cable (N4632-4, supplied with the control) as shown below. 8-PIN TRIGGER CONNECTOR 1 345678 8-PIN TRIGGER CONNECTOR 1 345678 KEY KEY (RED) (BLACK) (GREEN) +12 AUX. GND (-) OUTPUT 18 OUTPUT 17 (YELLOW) (PURPLE) (BLACK) (BLUE) OUTPUT 18 (GREEN) GND (-) (YELLOW) +12 AUX. (ORANGE) OUTPUT 17 (RED) COM SYNC DATA SA412OXM-1 CABLE 00-trigcon-003-V1 Figure 15a. On-Board Trigger Connector with SA4120XM-1 Cable for Use With 1361X10 Transformer 4-WIRE CABLE 00-trigcon-005-V2 Figure 15b. On-Board Trigger Connector with 4-Wire Cable for Trigger Use Only • Trigger outputs are normally high, and go low upon programmed condition. • The outputs can be programmed for inverted operation (normally low, go high) using *79 Menu mode. • Program these triggers using *80/*81 Menu modes as you would for any other relay output. • When using these outputs, note: pin 1 = output number 17 (trigger 1): 15 ohms to ground when closed (output low), open when off (output high, normal default); can be used to reset smoke detector power (must set "output normal low = yes" in *79 Menu mode, and set for zone type 54, fire zone reset, in *80 Menu mode); or can support 12V relay module (e.g., Altronix AX-RBS) that draws less than 100mA pin 5 = output number 18 (trigger 2): 100 ohms to ground when closed (output low); open when off (output high, normal default); or can support 12V relay module that draws less than 20mA UL If on-board triggers are used, the wiring between the control unit and the UL Listed device must be run in conduit, be no more than 3 feet apart and have no intervening barriers or walls. 2-12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
On-Board Triggers
Connect field wiring to the desired trigger pin on the 8-pin trigger connector centrally
located above the terminal strip.
•
If using 1361X10 transformer and powerline carrier devices, use the SA4120XM-1
cable (part of 4120TR Trigger Cable). See
Wiring the AC Transformer
section for
transformer connections.
•
If only using the on-board triggers, you can use a 4-wire cable (N4632-4, supplied
with the control) as shown below.
1
3
4
5
6
7
8
SA412OXM-1
CABLE
8-PIN TRIGGER CONNECTOR
KEY
00-trigcon-003-V1
+12 AUX.
DATA
COM
SYNC
GND (-)
OUTPUT 17
(RED)
OUTPUT 18
(GREEN)
(ORANGE)
(YELLOW)
(BLUE)
(PURPLE)
(BLACK)
4-WIRE
CABLE
00-trigcon-005-V2
+12 AUX.
GND (-)
OUTPUT 17
OUTPUT 18
(RED)
(YELLOW)
(BLACK)
(GREEN)
1
3
4
5
6
7
8
8-PIN TRIGGER CONNECTOR
KEY
Figure 15a. On-Board Trigger Connector
Figure 15b. On-Board Trigger Connector
with SA4120XM-1 Cable for Use With
with 4-Wire Cable for Trigger Use Only
1361X10 Transformer
•
Trigger outputs are normally high, and go low upon programmed condition.
•
The outputs can be programmed for inverted operation (normally low, go high) using
*79 Menu mode.
•
Program these triggers using *80/*81 Menu modes as you would for any other relay
output.
•
When using these outputs, note:
pin 1 =
output number 17 (trigger 1):
15 ohms to ground when closed (output low), open when off (output high, normal
default); can be used to reset smoke detector power (must set “output normal low
= yes” in *79 Menu mode, and set for zone type 54, fire zone reset, in *80 Menu
mode); or can support 12V relay module (
e.g., Altronix AX-RBS)
that draws less
than 100mA
pin 5 =
output number 18 (trigger 2):
100 ohms to ground when closed (output low); open when off (output high,
normal default); or can support 12V relay module that draws less than 20mA
U
L
If on-board triggers are used, the wiring between the control unit and the UL Listed device must
be run in conduit, be no more than 3 feet apart and have no intervening barriers or walls.
Installation and Setup Guide
2-12