Husqvarna V554 Owner Manual - Page 12

To set the cutting deck in transport position or mow position, To set the cutting height

Get Husqvarna V554 PDF manuals and user guides View all Husqvarna V554 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

• Pull out the drive system lever fully to disengage the drive system. The drive system lever is on the left side of the product. 3. Put the pin in the hole for the correct cutting height. 4. Push the transport latch lever forward to lower the cutting deck into mow position. To start the engine 1. Push the PTO button to disengage the drive on the cutting deck. • Push in the drive system lever fully to engage the drive system. To set the cutting deck in transport position or mow position The cutting deck must be in transport position during transportation. • Pull back the deck lifting lever (A) fully. The transport latch lever (B) locks the deck lifting lever in transport position. 2. Move the throttle lever to ½ throttle position. 3. Engage the parking brake. Refer to To disengage and engage the drive system on page 11. 4. If the engine is cold, pull up the choke control fully. A B 5. Push in and turn the ignition key to the start position. • Push the transport latch lever (B) forward to lower the cutting deck into mow position. To set the cutting height 1. Set the cutting deck in transport position. Refer to To set the cutting deck in transport position or mow position on page 12. 2. Push in the button on the top of the pin and pull the pin out. Note: Do not keep the ignition key in the start position for more than 5 seconds at a time. If the engine does not start, wait 15 seconds before you try again. 6. When the engine starts, immediately release the ignition key to the run position. 7. Slowly push in the choke control if the choke was used. 8. Let the engine run at ½ throttle for 3-5 minutes before you apply heavy load. 12 1995 - 002 - 05.12.2022

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
•
Pull out the drive system lever fully to disengage
the drive system. The drive system lever is on
the left side of the product.
•
Push in the drive system lever fully to engage the
drive system.
To set the cutting deck in transport
position or mow position
The cutting deck must be in transport position during
transportation.
•
Pull back the deck lifting lever (A) fully. The
transport latch lever (B) locks the deck lifting
lever in transport position.
A
B
•
Push the transport latch lever (B) forward to
lower the cutting deck into mow position.
To set the cutting height
1.
Set the cutting deck in transport position. Refer
to
To set the cutting deck in transport position or
mow position on page 12
.
2.
Push in the button on the top of the pin and pull
the pin out.
3.
Put the pin in the hole for the correct cutting
height.
4.
Push the transport latch lever forward to lower
the cutting deck into mow position.
To start the engine
1.
Push the PTO button to disengage the drive on
the cutting deck.
2.
Move the throttle lever to ½ throttle position.
3.
Engage the parking brake. Refer to
To
disengage and engage the drive system on page
11
.
4.
If the engine is cold, pull up the choke control
fully.
5.
Push in and turn the ignition key to the start
position.
Note:
Do not keep the ignition key in the start
position for more than 5 seconds at a time. If the
engine does not start, wait 15 seconds before
you try again.
6.
When the engine starts, immediately release the
ignition key to the run position.
7.
Slowly push in the choke control if the choke was
used.
8.
Let the engine run at ½ throttle for 3-5 minutes
before you apply heavy load.
12
1995 - 002 - 05.12.2022