Husqvarna V554 Owner Manual - Page 25

To lubricate the front wheels, To lubricate the cutting deck spindles, Troubleshooting

Get Husqvarna V554 PDF manuals and user guides View all Husqvarna V554 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

To lubricate the front wheels • Remove the dust cap (A). Grease the nipple (B) with a grease gun until grease comes out from the top washer. A B 2. Lubricate each cutting deck spindle 2-3 strokes. C • Lubricate the joint bearing of the front wheels (C) with a grease gun until grease comes out. To lubricate the cutting deck spindles 1. Set the cutting deck in mow position. Note: Use a grease gun with a rubber hose when you lubricate the cutting deck spindles. Troubleshooting Troubleshooting schedule If you cannot find a solution to your problems in this operator's manual, speak to your Husqvarna service agent. Problem Engine does not start. Cause The drive of the blades is engaged. Refer to PTO (Power TakeOff) button on page 4. Steering controls are not locked in the neutral position. The battery is too weak. Refer to To charge the battery on page 17. There is dirt in the carburetor or the fuel line. The fuel filter or fuel line is clogged. The ignition system is damaged. Incorrect neutral adjustment. Refer to To adjust the neutral position on page 19. 1995 - 002 - 05.12.2022 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
To lubricate the front wheels
•
Remove the dust cap (A). Grease the nipple (B)
with a grease gun until grease comes out from
the top washer.
A
B
C
•
Lubricate the joint bearing of the front wheels (C)
with a grease gun until grease comes out.
To lubricate the cutting deck
spindles
1.
Set the cutting deck in mow position.
2.
Lubricate each cutting deck spindle 2-3 strokes.
Note:
Use a grease gun with a rubber hose
when you lubricate the cutting deck spindles.
Troubleshooting
Troubleshooting schedule
If you cannot find a solution to your problems in this
operator's manual, speak to your Husqvarna service
agent.
Problem
Cause
Engine does not start.
The drive of the blades is engaged. Refer to
PTO (Power Take-
Off) button on page 4
.
Steering controls are not locked in the neutral position.
The battery is too weak. Refer to
To charge the battery on page
17
.
There is dirt in the carburetor or the fuel line.
The fuel filter or fuel line is clogged.
The ignition system is damaged.
Incorrect neutral adjustment. Refer to
To adjust the neutral posi-
tion on page 19
.
1995 - 002 - 05.12.2022
25