Home » Husqvarna Manuals » Lawn Mowers » Husqvarna V554 » Manual Viewer

Husqvarna V554 Owner Manual - Page 18

To connect the jumper cables, To remove and install the battery, Tire pressure

Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

The product that is used for the emergency start must also have a 12 V system with negative ground. To connect the jumper cables WARNING: Risk of explosion because of explosive gas that comes from the battery. Do not connect the negative terminal of the fully charged battery to or near the negative terminal of the weak battery. To remove and install the battery 1. Pull open the engine cover to get access to the battery. 2. Remove the knob from battery bracket and remove the bracket from the battery. CAUTION: Do not use the battery of the product to start other vehicles. 1. Connect one end of the red cable to the POSITIVE battery terminal (+) on the weak battery (A). C B D A 2. Connect the other end of the red cable to the POSITIVE battery terminal (+) on the fully charged battery (B). WARNING: Do not short circuit the ends of the red cable against the chassis. 3. Connect one end of the black cable to the NEGATIVE battery terminal (-) on the fully charged battery (C). 4. Connect the other end of the black cable to a CHASSIS GROUND (D), away from the fuel tank and the battery. To remove the jumper cables Note: Remove the jumper cables in the opposite sequence to how you connect them. 1. Remove the BLACK cable from the chassis. 2. Remove the BLACK cable from the fully charged battery. 3. Remove the RED cable from the 2 batteries. 3. Use 2 wrenches to disconnect the black battery cable from the negative (-) terminal on the battery. 4. Use 2 wrenches to disconnect the red battery cable from the positive (+) terminal on the battery. 5. Carefully remove the battery from the product. 6. Install in the opposite sequence. Tire pressure Make sure to have the correct tire pressure on all 4 tires. Refer to Technical data on page 29. To remove and install the front wheels 1. Remove the nut and the bolt to remove the front wheels from the forks. 2. Install in the opposite sequence. Torque the nut and bolt to 50 ft-lbs / 67.8 Nm. To adjust the anti-scalp rollers The anti-scalp rollers keep the cutting deck in the correct position on the ground and prevent lawn scalping in most terrain conditions. The anti-scalp rollers can be set in 3 positions for different lengths of grass: • Top position: 1.5-2.5 in. / 38-64 mm grass. 18 1995 - 002 - 05.12.2022

Section	Page
Contents	2
Conformity certificates	2
USA requirements	2
Introduction	2
Pre-delivery inspection and product numbers	2
Product description	3
Intended use	3
Product overview	3
Stand on or walk behind position	3
Steering controls	4
Operator Presence Control (OPC)	4
Ignition key	4
Throttle control	4
Choke control	4
PTO (Power Take-Off) button	4
Fuel gauge	5
Fuel shut-off valve	5
Fuses	5
Hour meter	5
Symbols on the product	5
Product liability	6
Safety	6
Safety definitions	6
General safety instructions	6
Safety instructions regarding children	7
Safety instructions for operation	7
Safety instructions for operation on slopes	7
Safety instructions for operation on slopes	8
Personal protective equipment	8
Safety devices on the product	8
To do a check of the ignition lock	8
Operation conditions	8
Parking brake	8
Muffler	8
To do a check of the muffler	9
Spark arrestor	9
Protective covers	9
Fuel safety	9
Transport safety	9
Hauling	9
Battery safety	9
Safety instructions for maintenance	9
Operation	10
Introduction	10
To operate the product for the first time	10
To do before you operate the product	10
To fill fuel	11
To set the product in stand on or walk behind position	11
To adjust the adjustable bar	11
To engage and disengage the parking brake	11
To disengage and engage the drive system	11
To set the cutting deck in transport position or mow position	12
To set the cutting height	12
To start the engine	12
To operate the product	13
To stop the engine	13
To adjust the tracking speed	14
To get a good cutting result	14
To do a 3-point turn	14
Maintenance	15
Introduction	15
Maintenance schedule	15
Maintenance schedule for the operator	15
To clean the product	17
To clean the engine and the muffler	17
To clean the battery	17
To remove the covers	17
To remove and install the engine cover	17
To do a check of the parking brake	17
To charge the battery	17
To do an emergency start of the engine	17
To connect the jumper cables	18
To remove the jumper cables	18
To remove and install the battery	18
Tire pressure	18
To remove and install the front wheels	18
To adjust the anti-scalp rollers	18
To adjust the parallelism of the cutting deck	19
To adjust the neutral position	19
To adjust the neutral switches	20
To examine the blades	20
To replace the blades	20
To remove the deck drive belt	21
To install the deck drive belt	21
To remove the deck belt	21
To install the deck belt	21
To remove the pump belt	22
To install the pump belt	22
To do a check of the engine oil level	22
To replace the engine oil	22
To do a check of the hydraulic oil level	23
Lubrication, general information	23
Lubrication schedule	24
To lubricate the front wheels	25
To lubricate the cutting deck spindles	25
Troubleshooting	25
Troubleshooting schedule	25
Transportation, storage and disposal	27
Transportation	27
Storage	27
Disposal	28
Technical data	29
Technical data	29
Battery charging times	30
Service	31
Service	31
Contenido	32
Certificados de conformidad	32
Requisitos para EE. UU.	32
Introducción	32
Inspección previa a la entrega y números de producto	32
Descripción del producto	33
Uso previsto	33
Descripción general del producto	33
Posición de caminar o permanecer de pie en la parte trasera	34
Controles de la dirección	34
Control de presencia del operador (OPC)	34
Llave de encendido	34
Control del acelerador	34
Estrangulador	35
Botón de toma de fuerza (PTO)	35
Indicador de combustible	35
Válvula de corte de combustible	35
Fusibles	35
Medidor de horas	35
Símbolos en el producto	35
Responsabilidad del fabricante	36
Seguridad	36
Definiciones de seguridad	36
Instrucciones generales de seguridad	37
Instrucciones de seguridad relacionadas con los niños	37
Instrucciones de seguridad para el funcionamiento	37
Instrucciones de seguridad para el uso en pendientes	38
Instrucciones de seguridad para el uso en pendientes	38
Equipo de protección personal	38
Dispositivos de seguridad en el producto	39
Para comprobar el bloqueo del encendido	39
Condiciones de funcionamiento	39
Freno de estacionamiento	39
Silenciador	39
Para revisar el silenciador	39
Apagachispas	39
Cubiertas protectoras	39
Seguridad de combustible	40
Seguridad del transporte	40
Transporte	40
Seguridad de la batería	40
Instrucciones de seguridad para el mantenimiento	40
Funcionamiento	41
Introducción	41
Para usar el producto por primera vez	41
Haga lo siguiente antes de usar el producto	41
Para agregar combustible	42
Para colocar el producto en posición de caminar o permanecer de pie en la parte trasera	42
Para ajustar la barra ajustable	42
Para acoplar y desacoplar el freno de estacionamiento	43
Para desacoplar y acoplar el sistema de transmisión	43
Para colocar el equipo de corte en la posición de transporte o posición de corte	43
Ajuste de la altura de corte	43
Para arrancar el motor	43
Para hacer funcionar el producto	44
Para detener el motor	45
Para ajustar la velocidad de desplazamiento	45
Para conseguir un buen resultado de corte	45
Para hacer un giro de 3 puntos	46
Mantenimiento	46
Introducción	46
Programa de mantenimiento	46
Programa de mantenimiento para el usuario	47
Para limpiar el producto	49
Para limpiar el motor y el silenciador	49
Para limpiar la batería	49
Para quitar las cubiertas	49
Para retirar e instalar la cubierta del motor	49
Para comprobar el freno de estacionamiento	49
Para cargar la batería	49
Para hacer una parada de emergencia del motor	50
Para conectar los cables de puente	50
Para retirar los cables de puente	50
Para retirar e instalar la batería	50
Presión de los neumáticos	50
Para retirar e instalar las ruedas delanteras	51
Para ajustar las ruedas de apoyo	51
Para ajustar el paralelismo del equipo de corte	51
Para ajustar la posición neutra	52
Para ajustar los interruptores de neutro	52
Para examinar las cuchillas	53
Para sustituir las hojas	53
Para retirar la correa de transmisión del equipo	53
Para instalar la correa de transmisión del equipo	53
Para extraer la correa del equipo	53
Para instalar la correa del equipo	54
Para extraer la correa de la bomba	54
Para instalar la correa de la bomba	54
Para revisar el nivel de aceite del motor	54
Para cambiar el aceite del motor:	55
Para revisar el nivel de aceite hidráulico	55
Lubricación; información general	56
Programa de lubricación	56
Para lubricar las ruedas delanteras	57
Para lubricar los ejes del equipo de corte	57
Solución de problemas	57
Programa de solución de problemas	57
Transporte, almacenamiento y eliminación de residuos	60
Transporte	60
Almacenamiento	60
Eliminación	60
Datos técnicos	61
Datos técnicos	61
Tiempos de carga de la batería	62
Servicio	63

Match case Limit results 1 per page

The product that is used for the emergency start

must also have a 12 V system with negative ground.

To connect the jumper cables

WARNING:

Risk of explosion

because of explosive gas that comes

from the battery. Do not connect the

negative terminal of the fully charged

battery to or near the negative terminal

of the weak battery.

CAUTION:

Do not use the battery of

the product to start other vehicles.

Connect one end of the red cable to the

POSITIVE battery terminal (+) on the weak

battery (A).

Connect the other end of the red cable to

the POSITIVE battery terminal (+) on the fully

charged battery (B).

WARNING:

Do not short circuit

the ends of the red cable against the

chassis.

Connect one end of the black cable to the

NEGATIVE battery terminal (-) on the fully

charged battery (C).

Connect the other end of the black cable to a

CHASSIS GROUND (D), away from the fuel tank

and the battery.

To remove the jumper cables

Note:

Remove the jumper cables in the opposite

sequence to how you connect them.

Remove the BLACK cable from the chassis.

Remove the BLACK cable from the fully charged

battery.

Remove the RED cable from the 2 batteries.

To remove and install the battery

Pull open the engine cover to get access to the

battery.

Remove the knob from battery bracket and

remove the bracket from the battery.

Use 2 wrenches to disconnect the black battery

cable from the negative (–) terminal on the

battery.

Use 2 wrenches to disconnect the red battery

cable from the positive (+) terminal on the

battery.

Carefully remove the battery from the product.

Install in the opposite sequence.

Tire pressure

Make sure to have the correct tire pressure on all 4

tires. Refer to

Technical data on page 29

To remove and install the front

wheels

Remove the nut and the bolt to remove the front

wheels from the forks.

Install in the opposite sequence. Torque the nut

and bolt to 50 ft-lbs / 67.8 Nm.

To adjust the anti-scalp rollers

The anti-scalp rollers keep the cutting deck in the

correct position on the ground and prevent lawn

scalping in most terrain conditions. The anti-scalp

rollers can be set in 3 positions for different lengths

of grass:

•

Top position: 1.5–2.5 in. / 38–64 mm grass.

1995 - 002 - 05.12.2022