Home » Husqvarna Manuals » Lawn Mowers » Husqvarna V554 » Manual Viewer

Husqvarna V554 Owner Manual - Page 17

To clean the product, To clean the engine and the muffler, To clean the battery, To remove the covers - stand on

Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

To clean the product CAUTION: Do not use a high- pressure washer or a steam cleaner. Water can go into bearings and electrical connections and cause corrosion which causes damage to the product. Clean the product immediately after use. • Do not clean hot surfaces such as the engine, muffler and exhaust system. Wait until the surfaces are cool, then remove the grass or dirt. • Before you clean with water, clean with a brush. Remove grass and dirt on and around the transmission, the transmission air intake, and the engine. • Use running water from a hose to clean the product. Do not use high-pressure. • Do not point the water at electrical components or bearings. Detergent usually increases the damage. • Use compressed air to clean the top side of the mower deck. • Use a water hose to clean below the cutting deck. • When the product is clean, start the cutting deck for a short period to remove remaining water. To clean the engine and the muffler Keep the engine and muffler free from grass cuttings and dirt. Grass cuttings soaked in fuel or oil on the engine can increase the fire risk and the risk that the engine becomes too hot. Let the engine cool before it is cleaned. Clean with water and a brush. Grass cuttings around the muffler dry quickly and are a fire risk. Use a brush or remove the grass cuttings with water when the muffler is cold. To clean the battery Corrosion and dirt on the battery and the terminals can cause the power of the battery to decrease. 1. Remove the battery. Refer to To remove and install the battery on page 18. 2. Flush the battery with water and let dry. CAUTION: Do not use a high- pressure washer or a steam cleaner. Water can go into bearings and electrical connections and cause corrosion which causes damage to the product. 3. Clean the terminals and the cable ends of the battery cables with a wire brush. To remove the covers To remove and install the engine cover The engine cover has a soft operator cushion that absorbs shocks during operation. 1. Lower the stand on platform. Refer to To set the product in stand on or walk behind position on page 11. 2. Pull the handle to open the engine cover fully. 3. Tilt the engine cover slightly up and lift the rear edge up to remove the engine cover. 4. Install in the opposite sequence. To do a check of the parking brake 1. Park the product on a slope with a hard surface. Note: Do not park the product on a grass slope when you do a check of the parking brake. 2. Engage the parking brake. 3. If the product starts to move with the parking brake engaged, let an approved service agent adjust the parking brake. 4. Disengage the parking brake. To charge the battery • Charge the battery if it is too weak to start the engine. Refer to Battery charging times on page 30 for battery charging times. • Use a standard battery charger. CAUTION: Do not use a boost charger or start booster. A boost charger or a start booster will cause damage to the electrical system of the product. • Always disconnect the battery charger before you start the engine. To do an emergency start of the engine If the battery is too weak to start the engine, you can use jumper cables to do an emergency start. This product has a 12 V system with negative ground. 1995 - 002 - 05.12.2022 17

Section	Page
Contents	2
Conformity certificates	2
USA requirements	2
Introduction	2
Pre-delivery inspection and product numbers	2
Product description	3
Intended use	3
Product overview	3
Stand on or walk behind position	3
Steering controls	4
Operator Presence Control (OPC)	4
Ignition key	4
Throttle control	4
Choke control	4
PTO (Power Take-Off) button	4
Fuel gauge	5
Fuel shut-off valve	5
Fuses	5
Hour meter	5
Symbols on the product	5
Product liability	6
Safety	6
Safety definitions	6
General safety instructions	6
Safety instructions regarding children	7
Safety instructions for operation	7
Safety instructions for operation on slopes	7
Safety instructions for operation on slopes	8
Personal protective equipment	8
Safety devices on the product	8
To do a check of the ignition lock	8
Operation conditions	8
Parking brake	8
Muffler	8
To do a check of the muffler	9
Spark arrestor	9
Protective covers	9
Fuel safety	9
Transport safety	9
Hauling	9
Battery safety	9
Safety instructions for maintenance	9
Operation	10
Introduction	10
To operate the product for the first time	10
To do before you operate the product	10
To fill fuel	11
To set the product in stand on or walk behind position	11
To adjust the adjustable bar	11
To engage and disengage the parking brake	11
To disengage and engage the drive system	11
To set the cutting deck in transport position or mow position	12
To set the cutting height	12
To start the engine	12
To operate the product	13
To stop the engine	13
To adjust the tracking speed	14
To get a good cutting result	14
To do a 3-point turn	14
Maintenance	15
Introduction	15
Maintenance schedule	15
Maintenance schedule for the operator	15
To clean the product	17
To clean the engine and the muffler	17
To clean the battery	17
To remove the covers	17
To remove and install the engine cover	17
To do a check of the parking brake	17
To charge the battery	17
To do an emergency start of the engine	17
To connect the jumper cables	18
To remove the jumper cables	18
To remove and install the battery	18
Tire pressure	18
To remove and install the front wheels	18
To adjust the anti-scalp rollers	18
To adjust the parallelism of the cutting deck	19
To adjust the neutral position	19
To adjust the neutral switches	20
To examine the blades	20
To replace the blades	20
To remove the deck drive belt	21
To install the deck drive belt	21
To remove the deck belt	21
To install the deck belt	21
To remove the pump belt	22
To install the pump belt	22
To do a check of the engine oil level	22
To replace the engine oil	22
To do a check of the hydraulic oil level	23
Lubrication, general information	23
Lubrication schedule	24
To lubricate the front wheels	25
To lubricate the cutting deck spindles	25
Troubleshooting	25
Troubleshooting schedule	25
Transportation, storage and disposal	27
Transportation	27
Storage	27
Disposal	28
Technical data	29
Technical data	29
Battery charging times	30
Service	31
Service	31
Contenido	32
Certificados de conformidad	32
Requisitos para EE. UU.	32
Introducción	32
Inspección previa a la entrega y números de producto	32
Descripción del producto	33
Uso previsto	33
Descripción general del producto	33
Posición de caminar o permanecer de pie en la parte trasera	34
Controles de la dirección	34
Control de presencia del operador (OPC)	34
Llave de encendido	34
Control del acelerador	34
Estrangulador	35
Botón de toma de fuerza (PTO)	35
Indicador de combustible	35
Válvula de corte de combustible	35
Fusibles	35
Medidor de horas	35
Símbolos en el producto	35
Responsabilidad del fabricante	36
Seguridad	36
Definiciones de seguridad	36
Instrucciones generales de seguridad	37
Instrucciones de seguridad relacionadas con los niños	37
Instrucciones de seguridad para el funcionamiento	37
Instrucciones de seguridad para el uso en pendientes	38
Instrucciones de seguridad para el uso en pendientes	38
Equipo de protección personal	38
Dispositivos de seguridad en el producto	39
Para comprobar el bloqueo del encendido	39
Condiciones de funcionamiento	39
Freno de estacionamiento	39
Silenciador	39
Para revisar el silenciador	39
Apagachispas	39
Cubiertas protectoras	39
Seguridad de combustible	40
Seguridad del transporte	40
Transporte	40
Seguridad de la batería	40
Instrucciones de seguridad para el mantenimiento	40
Funcionamiento	41
Introducción	41
Para usar el producto por primera vez	41
Haga lo siguiente antes de usar el producto	41
Para agregar combustible	42
Para colocar el producto en posición de caminar o permanecer de pie en la parte trasera	42
Para ajustar la barra ajustable	42
Para acoplar y desacoplar el freno de estacionamiento	43
Para desacoplar y acoplar el sistema de transmisión	43
Para colocar el equipo de corte en la posición de transporte o posición de corte	43
Ajuste de la altura de corte	43
Para arrancar el motor	43
Para hacer funcionar el producto	44
Para detener el motor	45
Para ajustar la velocidad de desplazamiento	45
Para conseguir un buen resultado de corte	45
Para hacer un giro de 3 puntos	46
Mantenimiento	46
Introducción	46
Programa de mantenimiento	46
Programa de mantenimiento para el usuario	47
Para limpiar el producto	49
Para limpiar el motor y el silenciador	49
Para limpiar la batería	49
Para quitar las cubiertas	49
Para retirar e instalar la cubierta del motor	49
Para comprobar el freno de estacionamiento	49
Para cargar la batería	49
Para hacer una parada de emergencia del motor	50
Para conectar los cables de puente	50
Para retirar los cables de puente	50
Para retirar e instalar la batería	50
Presión de los neumáticos	50
Para retirar e instalar las ruedas delanteras	51
Para ajustar las ruedas de apoyo	51
Para ajustar el paralelismo del equipo de corte	51
Para ajustar la posición neutra	52
Para ajustar los interruptores de neutro	52
Para examinar las cuchillas	53
Para sustituir las hojas	53
Para retirar la correa de transmisión del equipo	53
Para instalar la correa de transmisión del equipo	53
Para extraer la correa del equipo	53
Para instalar la correa del equipo	54
Para extraer la correa de la bomba	54
Para instalar la correa de la bomba	54
Para revisar el nivel de aceite del motor	54
Para cambiar el aceite del motor:	55
Para revisar el nivel de aceite hidráulico	55
Lubricación; información general	56
Programa de lubricación	56
Para lubricar las ruedas delanteras	57
Para lubricar los ejes del equipo de corte	57
Solución de problemas	57
Programa de solución de problemas	57
Transporte, almacenamiento y eliminación de residuos	60
Transporte	60
Almacenamiento	60
Eliminación	60
Datos técnicos	61
Datos técnicos	61
Tiempos de carga de la batería	62
Servicio	63

Match case Limit results 1 per page

To clean the product

CAUTION:

Do not use a high-

pressure washer or a steam cleaner.

Water can go into bearings and electrical

connections and cause corrosion which

causes damage to the product.

Clean the product immediately after use.

•

Do not clean hot surfaces such as the engine,

muffler and exhaust system. Wait until the

surfaces are cool, then remove the grass or dirt.

•

Before you clean with water, clean with a brush.

Remove grass and dirt on and around the

transmission, the transmission air intake, and the

engine.

•

Use running water from a hose to clean the

product. Do not use high-pressure.

•

Do not point the water at electrical components

or bearings. Detergent usually increases the

damage.

•

Use compressed air to clean the top side of the

mower deck.

•

Use a water hose to clean below the cutting

deck.

•

When the product is clean, start the cutting deck

for a short period to remove remaining water.

To clean the engine and the muffler

Keep the engine and muffler free from grass cuttings

and dirt. Grass cuttings soaked in fuel or oil on the

engine can increase the fire risk and the risk that the

engine becomes too hot. Let the engine cool before

it is cleaned. Clean with water and a brush.

Grass cuttings around the muffler dry quickly and are

a fire risk. Use a brush or remove the grass cuttings

with water when the muffler is cold.

To clean the battery

Corrosion and dirt on the battery and the terminals

can cause the power of the battery to decrease.

Remove the battery. Refer to

To remove and

install the battery on page 18

Flush the battery with water and let dry.

CAUTION:

Do not use a high-

pressure washer or a steam cleaner.

Water can go into bearings and

electrical connections and cause

corrosion which causes damage to

the product.

Clean the terminals and the cable ends of the

battery cables with a wire brush.

To remove the covers

To remove and install the engine cover

The engine cover has a soft operator cushion that

absorbs shocks during operation.

Lower the stand on platform. Refer to

To set the

product in stand on or walk behind position on

page 11

Pull the handle to open the engine cover fully.

Tilt the engine cover slightly up and lift the rear

edge up to remove the engine cover.

Install in the opposite sequence.

To do a check of the parking brake

Park the product on a slope with a hard surface.

Note:

Do not park the product on a grass

slope when you do a check of the parking brake.

Engage the parking brake.

If the product starts to move with the parking

brake engaged, let an approved service agent

adjust the parking brake.

Disengage the parking brake.

To charge the battery

•

Charge the battery if it is too weak to start the

engine. Refer to

Battery charging times on page

for battery charging times.

•

Use a standard battery charger.

CAUTION:

Do not use a boost

charger or start booster. A boost

charger or a start booster will cause

damage to the electrical system of

the product.

•

Always disconnect the battery charger before

you start the engine.

To do an emergency start of the

engine

If the battery is too weak to start the engine, you can

use jumper cables to do an emergency start. This

product has a 12 V system with negative ground.

1995 - 002 - 05.12.2022