IBM 865811Y User Guide - Page 34

Windows, driver, messages

Get IBM 865811Y - Netfinity 5100 - 8658 PDF manuals and user guides
UPC - 087944531869
View all IBM 865811Y manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Table 3. NDIS 2.01 (OS/2) driver messages for the Ethernet controller (continued) PCNTND-24 WARNING: PCNET IRQ does not match PROTOCOL.INI. Explanation: The interrupt request (IRQ) setting in the PROTOCOL.INI file does not match the hardware IRQ setting. Action: Remove the IRQ setting from the PROTOCOL.INI file or change the IRQ setting in the PROTOCOL.INI file to match the IRQ setting shown in the PCI Slot/Device Information selection of the Advanced Setup menu in the Configuration/Setup Utility program. PCNTND-25 PCI scan specified, PCI bus not found! Explanation: The driver cannot locate the PCI bus. Action: Run the diagnostic programs. PCNTND-29 WARNING: DMA number is not necessary for PCI device. Explanation: The Ethernet controller does not require a DMA setting. Action: Remove the DMA setting in the PROTOCOL.INI file. PCNTND-33 PCNET device with specified IOBASE is already in use. Explanation: The specified I/O address number is already in use by another Ethernet controller or device. Action: Remove the I/O address setting in the PROTOCOL.INI file. NDIS 4.0 (Windows NT) driver messages This section contains the error messages for the NDIS 4.0 drivers. The explanation and recommended action are included with each message. Table 4. NDIS (Windows NT) driver messages for the Ethernet controller PermaNet™Server: No Secondary Adapter Found. Grouping Mode is disabled. PermaNet Server: Explanation: The failover option requires an adapter that is compatible with the device driver of the Ethernet controller on the system board. No such adapter was found. Action: Make sure the correct adapter is installed. Problem Occurs on the Primary Adapter. Switching over to the Secondary Adapter. PermaNet Server: Explanation: The system detected a problem with the primary Ethernet connection and has transferred all network traffic to the secondary Ethernet controller. Action: identify the cause of the failure on the primary Ethernet connection. Restoring the operational state of the primary connection will cause the network traffic to automatically transfer to the primary Ethernet controller. Switching back to Primary Adapter. Explanation: The primary Ethernet connection is now operating correctly. Network traffic will automatically transfer to the primary Ethernet controller. Action: None needed, message is for information only. UNIX messages This section provides descriptions of the Ethernet error messages for the SCO UNIX LLI driver, and suggested actions to resolve each problem. 24 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
Table
3.
NDIS
2.01
(OS/2)
driver
messages
for
the
Ethernet
controller
(continued)
PCNTND-24
WARNING:
PCNET
IRQ
does
not
match
PROTOCOL.INI.
Explanation:
The
interrupt
request
(IRQ)
setting
in
the
PROTOCOL.INI
file
does
not
match
the
hardware
IRQ
setting.
Action:
Remove
the
IRQ
setting
from
the
PROTOCOL.INI
file
or
change
the
IRQ
setting
in
the
PROTOCOL.INI
file
to
match
the
IRQ
setting
shown
in
the
PCI
Slot/Device
Information
selection
of
the
Advanced
Setup
menu
in
the
Configuration/Setup
Utility
program.
PCNTND-25
PCI
scan
specified,
PCI
bus
not
found!
Explanation:
The
driver
cannot
locate
the
PCI
bus.
Action:
Run
the
diagnostic
programs.
PCNTND-29
WARNING:
DMA
number
is
not
necessary
for
PCI
device.
Explanation:
The
Ethernet
controller
does
not
require
a
DMA
setting.
Action:
Remove
the
DMA
setting
in
the
PROTOCOL.INI
file.
PCNTND-33
PCNET
device
with
specified
IOBASE
is
already
in
use.
Explanation:
The
specified
I/O
address
number
is
already
in
use
by
another
Ethernet
controller
or
device.
Action:
Remove
the
I/O
address
setting
in
the
PROTOCOL.INI
file.
NDIS
4.0
(Windows
NT)
driver
messages
This
section
contains
the
error
messages
for
the
NDIS
4.0
drivers.
The
explanation
and
recommended
action
are
included
with
each
message.
Table
4.
NDIS
(Windows
NT)
driver
messages
for
the
Ethernet
controller
PermaNet
™
Server:
No
Secondary
Adapter
Found.
Grouping
Mode
is
disabled.
Explanation:
The
failover
option
requires
an
adapter
that
is
compatible
with
the
device
driver
of
the
Ethernet
controller
on
the
system
board.
No
such
adapter
was
found.
Action:
Make
sure
the
correct
adapter
is
installed.
PermaNet
Server:
Problem
Occurs
on
the
Primary
Adapter.
Switching
over
to
the
Secondary
Adapter.
Explanation:
The
system
detected
a
problem
with
the
primary
Ethernet
connection
and
has
transferred
all
network
traffic
to
the
secondary
Ethernet
controller.
Action:
identify
the
cause
of
the
failure
on
the
primary
Ethernet
connection.
Restoring
the
operational
state
of
the
primary
connection
will
cause
the
network
traffic
to
automatically
transfer
to
the
primary
Ethernet
controller.
PermaNet
Server:
Switching
back
to
Primary
Adapter.
Explanation:
The
primary
Ethernet
connection
is
now
operating
correctly.
Network
traffic
will
automatically
transfer
to
the
primary
Ethernet
controller.
Action:
None
needed,
message
is
for
information
only.
UNIX
messages
This
section
provides
descriptions
of
the
Ethernet
error
messages
for
the
SCO
UNIX
LLI
driver,
and
suggested
actions
to
resolve
each
problem.
24
:
Netfinity
5100
Type
8658
Models
11Y,
21Y,
31Y,
41Y,
51Y,
1RY,
2RY,
3RY,
4RY,
5RY