IBM x3800 User Guide - Page 36

Removing, bezel

Get IBM x3800 - System - 8865 PDF manuals and user guides
UPC - 000435948984
View all IBM x3800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Top cover Cover release latch 1. Read the safety information that begins on page v and "Installation guidelines" on page 21. 2. If you are installing or replacing a non-hot-swap component, turn off the server and all peripheral devices. Disconnect the power cords; then, disconnect all external cables from the server. 3. Lift the plastic cover-release latch near the edge of the top cover. 4. Slide the top cover slightly toward the rear of the server; the cover will stop after moving approximately 25 mm (1 inch). Lift the cover off the server, and set the cover aside. Attention: For proper cooling and airflow, replace the top cover before turning on the server. Operating the server for more than 2 minutes with the top cover removed might damage server components. Removing the bezel On a tower model, make sure that you unlock or remove the front cover before you remove the top cover and bezel. To remove the bezel, complete the following steps: 24 IBM System x3800 Type 8865: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Top cover
Cover release
latch
1.
Read
the
safety
information
that
begins
on
page
v
and
“Installation
guidelines”
on
page
21.
2.
If
you
are
installing
or
replacing
a
non-hot-swap
component,
turn
off
the
server
and
all
peripheral
devices.
Disconnect
the
power
cords;
then,
disconnect
all
external
cables
from
the
server.
3.
Lift
the
plastic
cover-release
latch
near
the
edge
of
the
top
cover.
4.
Slide
the
top
cover
slightly
toward
the
rear
of
the
server;
the
cover
will
stop
after
moving
approximately
25
mm
(1
inch).
Lift
the
cover
off
the
server,
and
set
the
cover
aside.
Attention:
For
proper
cooling
and
airflow,
replace
the
top
cover
before
turning
on
the
server.
Operating
the
server
for
more
than
2
minutes
with
the
top
cover
removed
might
damage
server
components.
Removing
the
bezel
On
a
tower
model,
make
sure
that
you
unlock
or
remove
the
front
cover
before
you
remove
the
top
cover
and
bezel.
To
remove
the
bezel,
complete
the
following
steps:
24
IBM
System
x3800
Type
8865:
User’s
Guide