IBM x3800 User Guide - Page 45

Notes

Get IBM x3800 - System - 8865 PDF manuals and user guides
UPC - 000435948984
View all IBM x3800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Cable retention clip Tape drive end of cable Cable channel Full-high tape drive installation hardware Notes: 1. For clarity, the media-signal cable and other cables are not shown in the illustration. 2. The tape drive might come with a round cable, as shown in the illustration, or a ribbon cable. The following illustration shows how to install a hot-swap hard disk drive. Filler panel Hard disk drive assembly Drive handle (open position) 5.25-inch bays for supported tape drives To install a hot-swap hard disk drive, complete the following steps: 1. Read the safety information that begins on page v, and "Installation guidelines" on page 21. 2. If you are installing drives in a tower model, remove the front cover (see "Removing the front cover, top cover, and bezel" on page 23). Chapter 2. Installing options 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Cable retention clip
Cable channel
Tape drive
end of cable
Full-high tape drive
installation hardware
Notes:
1.
For
clarity,
the
media-signal
cable
and
other
cables
are
not
shown
in
the
illustration.
2.
The
tape
drive
might
come
with
a
round
cable,
as
shown
in
the
illustration,
or
a
ribbon
cable.
The
following
illustration
shows
how
to
install
a
hot-swap
hard
disk
drive.
Hard disk drive assembly
Drive handle
(open position)
Filler panel
5.25-inch bays for
supported tape drives
To
install
a
hot-swap
hard
disk
drive,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
v,
and
“Installation
guidelines”
on
page
21.
2.
If
you
are
installing
drives
in
a
tower
model,
remove
the
front
cover
(see
“Removing
the
front
cover,
top
cover,
and
bezel”
on
page
23).
Chapter
2.
Installing
options
33