IBM x3800 User Guide - Page 37

Installing, hot-swap, power, supply

Get IBM x3800 - System - 8865 PDF manuals and user guides
UPC - 000435948984
View all IBM x3800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Bezel 1. Press on the two release latches at the top edge of the bezel, and pull the top of the bezel slightly away from the server. 2. Lift the bezel to release the two tabs at the bottom edge of the bezel. 3. Store the bezel in a safe place. Installing a hot-swap power supply The following notes describe information that you must consider when installing a hot-swap power supply in the server: v The server comes with a minimum of two power supplies and supports up to three power supplies. v The power supplies are numbered from left to right (1 through 3) as viewed from the rear of the server. Power supplies must be installed in the following sequence: power supply 1 through power supply 3. v If you install or remove a power supply, observe the following precautions: Chapter 2. Installing options 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Bezel
1.
Press
on
the
two
release
latches
at
the
top
edge
of
the
bezel,
and
pull
the
top
of
the
bezel
slightly
away
from
the
server.
2.
Lift
the
bezel
to
release
the
two
tabs
at
the
bottom
edge
of
the
bezel.
3.
Store
the
bezel
in
a
safe
place.
Installing
a
hot-swap
power
supply
The
following
notes
describe
information
that
you
must
consider
when
installing
a
hot-swap
power
supply
in
the
server:
v
The
server
comes
with
a
minimum
of
two
power
supplies
and
supports
up
to
three
power
supplies.
v
The
power
supplies
are
numbered
from
left
to
right
(1
through
3)
as
viewed
from
the
rear
of
the
server.
Power
supplies
must
be
installed
in
the
following
sequence:
power
supply
1
through
power
supply
3.
v
If
you
install
or
remove
a
power
supply,
observe
the
following
precautions:
Chapter
2.
Installing
options
25