Icom IC-7300 Instruction Manual basic - Page 58

Connectors

Get Icom IC-7300 PDF manuals and user guides View all Icom IC-7300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

8 SET MODE Connectors ACC/USB Output Select (Default: AF) Selects the signal output from [ACC] and [USB]. ACC/USB AF Output Level (Default: 50%) Sets the AF output level of [ACC] and [USB]. ACC/USB AF SQL (Default: OFF (OPEN)) Selects whether or not to output the audio from [ACC] and [USB], according to the squelch state. The same audio signals are output from [USB] and [ACC]. ACC/USB AF Beep/Speech... Output (Default: OFF) Sets the Beep and Speech audio output condition of [ACC] and [USB]. LYou should set the "ACC/USB AF SQL" item to "AF." LThe beep level is limited when the "Beep Level Limit" item is "ON." ACC/USB IF Output Level (Default: 50%) Sets the IF output level of [ACC] and [USB]. ACC MOD Level (Default: 50%) Sets the modulation input level of [ACC]. USB MOD Level (Default: 50%) Sets the modulation input level of [USB]. DATA OFF MOD (Default: MIC,ACC) Selects the connector(s) to input the modulation signal when the data mode is OFF. DATA MOD (Default: ACC) Selects the connector(s) to input the modulation signal when the data mode is ON. External Keypad VOICE (Default: OFF) Enables voice memory transmission using an external keypad. External Keypad KEYER (Default: OFF) Enables keyer memory transmission using an external keypad. External Keypad RTTY (Default: OFF) Enables RTTY memory transmission using an external keypad. CI-V Baud Rate (Default: Auto) Selects the CI-V data transfer rate. LWhen "Auto" is selected, the baud rate is automatically set according to the data rate of the connected controller. CI-V Address (Default: 94h) Selects the CI-V address. L"94h" is the default address of IC-7300. CI-V Transceive (Default: ON) Turns the Transceive function ON or OFF. CI-V USB→REMOTE Transceive Address(Default: 00h) Sets the address used to remotely control the transceiver or receiver using the optional RS-BA1, through the [USB] port. The external equipment control signal is output from the [REMOTE] port. CI-V Output (for ANT) (Default: OFF) Enables outputting the antenna controller status (frequency and so on) from the [REMOTE] port. LAddress "01h" is reserved. The usable addresses are limited to 02h ~ DFh. CI-V USB Port (Default: Link to [REMOTE]) Selects the internal connection type between the [USB] and [REMOTE] CI-V ports. CI-V USB Baud Rate (Default: Auto) Selects the CI-V data transfer rate when remotely controlling the IC-7300 through the [USB] CI-V port. LWhen "Auto" is selected, the baud rate is automatically set according to the data rate of external controller. LThis setting is valid only when the "CI-V USB Port" item is set to "Unlink from [REMOTE]." CI-V USB Echo Back (Default: OFF) Turns the Data Echo Back function ON or OFF, when remotely controlling the IC-7300 through the [USB] CI-V port. LThis setting is valid only when the "CI-V USB Port" item is set to "Unlink from [REMOTE]." USB Serial Function (Default: CI-V) Selects the signal output from [USB]. 8-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
8
SET MODE
8-5
Connectors
ACC/USB Output Select
(Default: AF)
Selects the signal output from [ACC] and [USB].
ACC/USB AF Output Level
(Default: 50%)
Sets the AF output level of [ACC] and [USB].
ACC/USB AF SQL
(Default: OFF (OPEN))
Selects whether or not to output the audio from [ACC]
and [USB], according to the squelch state.
The same audio signals are output from [USB] and
[ACC].
ACC/USB AF Beep/Speech... Output
(Default: OFF)
Sets the Beep and Speech audio output condition of
[ACC] and [USB]
.
L
You should set the “ACC/USB AF SQL” item to “AF.”
L
The beep level is limited when the “Beep Level
Limit” item is “ON.”
ACC/USB IF Output Level
(Default: 50%)
Sets the IF output level of [ACC] and [USB].
ACC MOD Level
(Default: 50%)
Sets the modulation input level of [ACC].
USB MOD Level
(Default: 50%)
Sets the modulation input level of [USB].
DATA OFF MOD
(Default: MIC,ACC)
Selects the connector(s) to input the modulation signal
when the data mode is OFF.
DATA MOD
(Default: ACC)
Selects the connector(s) to input the modulation signal
when the data mode is ON.
Extern±l Keyp±d VOICE
(Default: OFF)
Enables voice memory transmission using an external
keypad.
Extern±l Keyp±d KEYER
(Default: OFF)
Enables keyer memory transmission using an external
keypad.
Extern±l Keyp±d RTTY
(Default: OFF)
Enables RTTY memory transmission using an
external keypad.
CI-V B±ud R±te
(Default: Auto)
Selects the CI-V data transfer rate.
L
When “Auto” is selected, the baud rate is
automatically set according to the data rate of the
connected controller.
CI-V Address
(Default: 94h)
Selects the CI-V address.
L
“94h” is the default address of IC-7300.
CI-V Tr±nsceive
(Default: ON)
Turns the Transceive function ON or OFF.
CI-V USB→REMOTE Transceive Address
(Default: 00h)
Sets the address used to remotely control the
transceiver or receiver using the optional RS-BA1,
through the [USB] port.
The external equipment control signal is output from
the [REMOTE] port.
CI-V Output (Nor A²T)
(Default: OFF)
Enables outputting the antenna controller status
(frequency and so on) from the [REMOTE] port.
L
Address “01h” is reserved.
The usable addresses are limited to 02h ~ DFh.
CI-V USB Port
(Default: Link to [REMOTE])
Selects the internal connection type between the
[USB] and [REMOTE] CI-V ports.
CI-V USB B±ud R±te
(Default: Auto)
Selects the CI-V data transfer rate when remotely
controlling the IC-7300 through the
[USB]
CI-V port
.
L
When “Auto” is selected, the baud rate is
automatically set according to the data rate of
external controller.
L
This setting is valid only when the “CI-V USB Port”
item is set to “Unlink from [REMOTE].”
CI-V USB Echo B±ck
(Default: OFF)
Turns the Data Echo Back function ON or OFF, when
remotely controlling the IC-7300 through the [USB]
CI-V port.
L
This setting is valid only when the “CI-V USB Port”
item is set to “Unlink from [REMOTE].”
USB Seri±l Function
(Default: CI-V)
Selects the signal output from [USB].