Icom IC-F3003 Instruction Manual - Page 19

Basic Operation

Get Icom IC-F3003 PDF manuals and user guides View all Icom IC-F3003 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

3 BASIC OPERATION ■ Turning power ON 1 Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. (p. 23) ➥ Rotate [VOL] to turn power ON. [VOL] 2 3 4 5 D Battery type selection 6 The battery type must be selected according to the battery pack or case when it is changed, but only the first time it is used. 7 Check the battery type before you begin the selection procedure. 8 One to three beep(s) sound in sequence, so you must repeat the steps until the number of beeps matches your battery type. 9 For example, if your battery type is a Li-ion battery pack, you must 10 repeat the procedure until 1 beep is heard. q Set [ROTARY SELECTOR] to any [ROTARY SELECTOR] 11 channel other than Channel 16. [VOL] 12 w Rotate [VOL] to turn the transceiv- er power OFF. 13 e W hile pushing and holding [PTT], rotate [VOL] to turn the power ON. 14 • You should hold [PTT] until the 15 beeps sound. (It takes approximate- [PTT] ly 5 seconds; while holding down 16 [PTT], the count down beeps sound. After that, a long beep sounds.) 17 • 1 beep sounds after the long beep when the Li-ion battery is selected. 18 • 2 beeps sound after the long beep when the battery case is selected. • 3 beeps sound after the long beep when the Ni-MH battery is selected. 19 r After the beep sounds, release [PTT]. t Repeat steps w to r until you select the attached battery type. 20 NOTE: This operation may not be available, depending on the presetting. Ask your dealer for details. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
12
3
BASIC OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
■
Turning power ON
Prior to using the transceiver for the first
time, the battery pack must be fully charged
for optimum life and operation. (p. 23)
➥
Rotate [VOL] to turn power ON.
D
Battery type selection
The battery type must be selected according to the battery pack or
case when it is changed, but only the first time it is used.
Check the battery type before you begin the selection procedure.
One to three beep(s) sound in sequence, so you must repeat the
steps until the number of beeps matches your battery type.
For example, if your battery type is a Li-ion battery pack, you must
repeat the procedure until 1 beep is heard.
q
Set
[ROTARY SELECTOR] to any
channel other than Channel 16.
w
Rotate [VOL] to t
urn the transceiv-
er power OFF.
e
While pushing and holding [PTT],
rotate [VOL] to turn the power ON.
• You should hold [PTT] until the
beeps sound. (It takes approximate-
ly 5 seconds; while holding down
[PTT], the count down beeps sound.
After that, a long beep sounds.)
•
1 beep sounds after the long beep when the Li-ion battery is selected.
•
2 beeps sound after the long beep when the battery case is selected.
•
3 beeps sound after the long beep when the Ni-MH battery is selected.
r
After the beep sounds, release [PTT].
t
Repeat steps
w
to
r
until you select the attached battery type.
NOTE:
This operation may not be available, depending on the
presetting. Ask your dealer for details.
[VOL]
[VOL]
[PTT]
[ROTARY SELECTOR]