Icom IC-M330G Instruction Manual english - Page 19

PREPARATIONS, Entering the MMSI code

Get Icom IC-M330G PDF manuals and user guides View all Icom IC-M330G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

■■Entering the MMSI code The Maritime Mobile Service Identity (MMSI: DSC self ID) code consists of 9 digits. You can only enter the code when turning ON the transceiver for the first time. This initial code entry can be done only once. After entering, it can be changed only by your dealer or distributor. If your MMSI code has already been entered, doing the steps below is not necessary. 1. Hold down [DIAL] to turn ON the transceiver. ••Three short beeps sound, and "Push [ENT] to Register your MMSI" is displayed. 2. Push [ENT] to start entering the MMSI code. ••The "MMSI Input" screen is displayed. LLPush [CLR] twice to skip the entry. If you skip the entry, you cannot make a DSC call. To enter the code after skipping, turn OFF the power, and then turn it ON again. 3. Enter the MMSI code. TIP: ••Select a number using [◄] and Push [ENT] to enter the selected number. ••Select "←" or "→," or rotate [DIAL] to move the cursor. 3 PREPARATIONS 1 4. Repeat step 3 to enter all 9 digits. 2 5. Push the software key below FIN to set the entered 3 code. ••The "Confirmation" screen is displayed. 4 6. Enter your MMSI code again to confirm. 5 6 7 7. Push FIN to set the entered code. 8 ••When your MMSI code is successfully entered, "MMSI 9 Successfully Registered" is briefly displayed, and then enters the operating screen. 10 11 12 13 LLYour MMSI code is also displayed on the operating screen. 14 15 16 NOTE: Except for the USA and Australian versions, the ATIS ID is also required to be set. See the next page and set it. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
7
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PREPARATIONS
■
Entering the MMSI code
The Maritime Mobile Service Identity (MMSI: DSC self ID)
code consists of 9 digits. You can only enter the code when
turning ON the transceiver for the first time.
4.
Repeat step 3 to enter all 9 digits.
5.
Push
the software key below
FIN
to set the entered
code.
•
The “Confirmation” screen is displayed.
6.
Enter your MMSI code again to confirm.
7.
Push
FIN
to set the entered code.
• When your MMSI code is successfully entered, “MMSI
Successfully Registered” is briefly displayed, and then
enters the operating screen.
L
Your MMSI code is also displayed on the operating screen.
This initial code entry can be done only once.
After entering, it can be changed only by your dealer
or distributor. If your MMSI code has already been
entered, doing the steps below is not necessary.
1.
Hold down [DIAL] to turn ON the transceiver.
• Three short beeps sound, and “Push [ENT] to Register your
MMSI” is displayed.
2.
Push [ENT] to start entering the MMSI code.
•
The “MMSI Input” screen is displayed.
L
Push [CLR] twice to skip the entry.
If you skip the entry, you cannot make a DSC call. To enter
the code after skipping, turn OFF the power, and then turn
it ON again.
3.
Enter the MMSI code.
NOTE:
Except for the USA and Australian versions, the
ATIS ID is also required to be set. See the next page and
set it.
TIP:
•
Select a number using [◄] and [►].
• Push [ENT] to enter the selected number.
•
Select “←” or “→,” or rotate [DIAL] to move the cursor.