Icom IC-M36 Service Manual - Page 13

Introduction, Ic-m35, Never, Do Not, <order Example&gt, Always, Unit Abbreviations, Model, Version - vhf marine transceiver

Get Icom IC-M36 PDF manuals and user guides View all Icom IC-M36 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

INTRODUCTION This service manual describes the latest technical information for the IC-M35 and IC-M36 VHF MARINE TRANSCEIVER at the time of publication. MODEL IC-M35 IC-M36 VERSION [CHN] [EUR] [UK] [FRG] [HOL] [AUS] [USA] [SEA] AC ADAPTER BC-174E N/A BC-174E BM-95V BC-147SA BC-174E TX Hi-POWER 6 W 6 W (1 W) 6 W 5 W 6 W To upgrade quality, any electrical or mechanical parts and internal circuits are subject to change without notice or obligation. UNIT ABBREVIATIONS: CH=CHASSIS M=MAIN UNIT CAUTION NEVER connect the transceiver to an AC outlet or to a DC power supply that uses more than specified. This will ruin the transceiver. DO NOT reverse the polarities of the power supply when connecting the transceiver. DO NOT apply an RF signal of more than 20 dBm (100 mW) to the antenna connector. This could damage the transceiver's front-end. (IC-M36) ORDERING PARTS Be sure to include the following four points when ordering replacement parts: 1. 10-digit Icom parts numbers 2. Component name 3. Equipment model name and unit name 4. Quantity required 1110003491 S.IC TA31136FNG IC-M36 8820001210 Screw 2438 screw IC-M35 MAIN UNIT 5 pieces Top cover 10 pieces Addresses are provided on the inside back cover for your convenience. REPAIR NOTES 1. Make sure that the problem is internal before disassembling the transceiver. 2. DO NOT open the transceiver until the transceiver is disconnected from its power source. 3. DO NOT force any of the variable components. Turn them slowly and smoothly. 4. DO NOT short any circuits or electronic parts. An insulated tuning tool MUST be used for all adjustments. 5. DO NOT keep power ON for a long time when the transceiver is defective. 6. DO NOT transmit power into a Standard Signal Generator or a Sweep Generator. 7. ALWAYS connect a 50 dB to 60 dB attenuator between the transceiver and a Deviation Meter or Spectrum Analyzer when using such test equipment. 8. READ the instructions of test equipment throughly before connecting a test equipment to the transceiver. Icom, Icom Inc. and ICOM logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
This service manual describes the latest technical
information for the
IC-M35
and
IC-M36
VHF MARINE
TRANSCEIVER at the time of publication.
NEVER
connect the transceiver to an AC outlet or to a DC
power supply that uses more than specified.
This will ruin
the transceiver.
DO NOT
reverse the polarities of the power supply when
connecting the transceiver.
DO NOT
apply an RF signal of more than 20 dBm (100 mW) to
the antenna connector. This could damage the transceiver’s
front-end.
To upgrade quality, any electrical or mechanical parts and
internal circuits are subject to change without notice or
obligation.
Be sure to include the following four points when ordering
replacement parts:
1. 10-digit Icom parts numbers
2. Component name
3. Equipment model name and unit name
4. Quantity required
<ORDER EXAMPLE>
1110003491 S.IC
TA31136FNG IC-M36
MAIN UNIT
5 pieces
8820001210 Screw 2438 screw
IC-M35
Top cover
10 pieces
Addresses are provided on the inside back cover for your
convenience.
Icom, Icom Inc. and ICOM logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United
Kingdom, Germany, France, Spain, Russia and/or other countries.
ORDERING PARTS
1. Make sure that the problem is internal before
disassembling the transceiver.
2.
DO NOT
open the transceiver until the transceiver is
disconnected from its power source.
3.
DO NOT
force any of the variable components.
Turn
them slowly and smoothly.
4.
DO NOT
short any circuits or electronic parts.
An
insulated tuning tool
MUST
be used for all adjustments.
5.
DO NOT
keep power ON for a long time when the
transceiver is defective.
6.
DO NOT
transmit power into a Standard Signal
Generator or a Sweep Generator.
7.
ALWAYS
connect a 50 dB to 60 dB attenuator between
the transceiver and a Deviation Meter or Spectrum
Analyzer when using such test equipment.
8.
READ
the instructions of test equipment throughly
before connecting a test equipment to the transceiver.
REPAIR NOTES
INTRODUCTION
CAUTION
UNIT ABBREVIATIONS:
CH=CHASSIS
M=MAIN UNIT
MODEL
VERSION
AC
ADAPTER
TX
Hi-POWER
IC-M35
[CHN]
BC-174E
6 W
[EUR]
[UK]
N/A
[FRG]
BC-174E
6 W (1 W)
[HOL]
6 W
[AUS]
BM-95V
5 W
IC-M36
[USA]
BC-147SA
6 W
[SEA]
BC-174E
(IC-M36)