Icom IC-R8600 I/q Output Reference Guide

Icom IC-R8600 Manual

Get Icom IC-R8600 PDF manuals and user guides View all Icom IC-R8600 manuals
Add to My Manuals
Save this manual to your list of manuals

Icom IC-R8600 manual content summary:

  • Icom IC-R8600 | I/q Output Reference Guide - Page 1
    I/Q OUTPUT REFERENCE GUIDE COMMUNICATIONS RECEIVER iR8600
  • Icom IC-R8600 | I/q Output Reference Guide - Page 2
    Communication through the [I/Q OUT] port ......... 3 DDGeneral description 3 DDAbout the GUID 3 DDAbout the endpoint 3 ■■About the I/Q signals 4 DDGeneral description 4 10 DDI/Q Output setting 11 ■■Operations while the IC-R8600 is in the I/Q mode ... 13 DDOperation limitations in the I/Q mode
  • Icom IC-R8600 | I/q Output Reference Guide - Page 3
    Requirement: ••IC-R8600 firmware must be version 1.3 or later. ••Windows 7 /8.1/10 PC (32 bit or 64 bit) ••USB 2.0 or higher ••USB I/Q driver (USB I/Q Package for HDSDR) You can download it from the Icom web site. (The software is commonly used with HDSDR*.) *An SDR receive software (freeware). You
  • Icom IC-R8600 | I/q Output Reference Guide - Page 4
    for HDSDR) that can be downloaded from Icom web site. After the driver is installed, you can receive I/Q signals and control the IC-R8600 through the WinUSB, using an I/Q receive software (user supplied). To use WinUSB, you need to set the driver's GUID and appropriate "endpoint." Refer to the next
  • Icom IC-R8600 | I/q Output Reference Guide - Page 5
    I/Q SIGNAL ■■About the I/Q signals DDGeneral description I/Q data is output from the [I/Q OUT] port on the IC-R8600. 1 endpoint is reserved to receive I/Q signals. I/Q data IC-R8600 → PC Address (Hexadecimal) 86 Direction Endpoint Number (Hexadecimal) IN 06 Transfer Type Bulk transfer The
  • Icom IC-R8600 | I/q Output Reference Guide - Page 6
    I/Q SIGNAL ■■I/Q data details DD24-bit long I/Q data Data format: The I/Q data is composed of 3 parts: "I" signals, "Q" signals and Synchronous signals. Each data length is: "I" = 24 bits (3 Bytes), "Q" =24 bits (3 Bytes), Synchronous data=48 bits (6 Bytes). (The byte order is in the little-endian
  • Icom IC-R8600 | I/q Output Reference Guide - Page 7
    frequency (0 Hz). A lower sampling frequency makes the DC component level greater. DC component An example of the DC component that is monitored on the HDSDR software. (Display frequency= 7 MHz, Sampling frequency=240 kHz) 6
  • Icom IC-R8600 | I/q Output Reference Guide - Page 8
    ) Direction Endpoint Number (Hexadecimal) Transfer Type Control command IC-R8600 → PC 88 IN 08 Bulk transfer Control command PC → IC-R8600 02 OUT 02 Bulk transfer LThe control command format is based on the ICOM Communication Interface V (CI-V) format. LThere are 2 command types
  • Icom IC-R8600 | I/q Output Reference Guide - Page 9
    format: Send a request command from the PC to request to return an IC-R8600 setting value. A reading command is composed of only a command number. The IC-R8600 will return the requested setting value as an acknowledgement when receiving the command. If the request command is invalid, "NG (FA)" will
  • Icom IC-R8600 | I/q Output Reference Guide - Page 10
    ). Command Number Sub command Number Data Command Function 05 See p.10 Set the receive frequency. 11* 00, 10, Send/read the Attenuator 20, 30 (0 0=ATT OFF mode is ON Usable Usable Usable Usable Usable Usable Usable Usable Usable Usable 02 00/01 Send/read HF band BPF setting (00=OFF, 01=ON)
  • Icom IC-R8600 | I/q Output Reference Guide - Page 11
    capacity, "NG (FA)" will be returned. To read the number of the edge, send command "1A 0E" (The Read Receive Band Edge Count command). IC-R8600 to PC (Read data format) q w e r t y u i o !0 !1 !2 XX XXXXXXXXXX 2 DXXXXXXXXXX Edge number 01~XX* 10 Hz digit: 0 ~ 9 1 Hz digit: 0 ~ 9 1 kHz digit
  • Icom IC-R8600 | I/q Output Reference Guide - Page 12
    can set the I/Q output to ON. When the sent command is valid and accepted by the IC-R8600, the acknowledgement "OK (FB)" will be returned. "NG (FA)" will be returned if invalid - 00: 16-bit 01: 24-bit - 01 5.12 MHz 04 960 kHz 02 3.84 MHz 05 480 kHz 03 1.92 MHz 06 240 kHz NOTE: The combination of
  • Icom IC-R8600 | I/q Output Reference Guide - Page 13
    I/Q SIGNAL ■■ Control commands relative to I/Q port setting DDI/Q Output setting (Continued) IC-R8600 to PC (Read data format): Reads the I/Q output settings. • When the I/Q signal output is OFF I/Q - 00: 16 bit 01: 24 bit - 01 5.12 MHz 04 960 kHz 02 3.84 MHz 05 480 kHz 03 1.92 MHz 06 240 kHz 12
  • Icom IC-R8600 | I/q Output Reference Guide - Page 14
    push the [LOCAL] key on the IC-R8600 front panel. Turning OFF the IC-R8600's power also exits the I/Q mode. While the IC-R8600 is in the I/Q mode, the returned to the condition/state before entering the I/Q mode. Receive setting: While in the I/Q mode, the receive mode is fixed to "USB," and "AGC" is
  • Icom IC-R8600 | I/q Output Reference Guide - Page 15
    A7375-11EX © 2018 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
I/Q OUTPUT REFERENCE GUIDE
iR8600
COMMUNICATIONS RECEIVER