Insignia NS-FDRE80W3 User Manual - Page 29

Step 5: Connect the gas line for gas models only, Important

Get Insignia NS-FDRE80W3 PDF manuals and user guides View all Insignia NS-FDRE80W3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

INSTALLATION INSTRUCTIONS 8 Cu. Ft. Electric and Gas Dryers Step 5: Connect the gas line (for gas models only) Important: Before you connect the gas line, review the gas line requirements in Gas requirements on page 19. 1 Remove the pipe thread protective cap from the gas inlet. Gas inlet on back of dryer 2 Apply a pipe joint compound or about 1.5 in. wraps of teflon tape over all threaded connections. The pipe joint compound must be resistant to the actions of any liquefied petroleum gas. 3 Connect all the pipe joints and tighten with a wrench. Note: An additional fitting is required to connect the 3/4 in. (1.9 cm) female thread end of a flexible connector to the 3/8 in. (1 cm) male threaded end on your dryer. Use only new AGA or CSA certified gas supply line with SS flexible connectors. The National Fuel Gas Code requires that an accessible, approved manual gas shutoff valve be installed within 6 in. (15 cm) of your dryer. Manual shutoff valve Flare union Flare union Nipple Flexible connector 4 Connect the gas supply to your dryer. Gas inlet on back of dryer 5 Securely tighten the gas line fitting over the threads. www.insigniaproducts.com 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
29
www.insigniaproducts.com
8 Cu. Ft. Electric and Gas Dryers
INSTALLATION INSTRUCTIONS
Step 5: Connect the gas line (for gas models only)
1
Remove the pipe thread protective cap from the gas inlet.
2
Apply a pipe joint compound or about 1.5 in. wraps of teflon tape over all
threaded connections. The pipe joint compound must be resistant to the
actions of any liquefied petroleum gas.
3
Connect all the pipe joints and tighten with a wrench.
4
Connect the gas supply to your dryer.
5
Securely tighten the gas line fitting over the threads.
Important:
Before you connect the gas line, review the gas line requirements
in Gas requirements
on page 19
.
Note:
An additional fitting is required to connect the 3/4 in. (1.9 cm) female
thread end of a flexible connector to the 3/8 in. (1 cm) male threaded end on
your dryer. Use only new AGA or CSA certified gas supply line with SS flexible
connectors. The National Fuel Gas Code requires that an accessible, approved
manual gas shutoff valve be installed within 6 in. (15 cm) of your dryer.
Gas inlet on back of dryer
Nipple
Flexible connector
Flare union
Flare union
Manual shutoff valve
Gas inlet on back of dryer