Insignia NS-LCD52HD-09 User Manual (English) - Page 20

Troubleshooting remote control, programming

Get Insignia NS-LCD52HD-09 PDF manuals and user guides View all Insignia NS-LCD52HD-09 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

To program a mode-dependent macro: 1 Press the device mode key (TV, DVD, STB, or AUX). 2 Press and hold SET until the LED blinks twice, then release. 3 Press 9 7 8. The LED blinks twice. 4 Press the key you wish to assign to a macro. 5 Enter the series of commands you want the macro to execute (up to 15 commands). 6 Press and hold SET until the red LED blinks twice, then release. Now, when you press the macro key, the remote sends the series of commands you have entered, but only if you are in the mode you selected in Step 1. For example, you could program the macro key to turn on both your TV and cable box and select a particular channel, but only if you are in TV mode. If you are in DVD mode, this key does not execute the macro you set up in TV mode. 7 To clear the macro, repeat Steps 1-6, but do not enter a series of commands at Step 5. Troubleshooting remote control programming Problem: The LED does not blink when you press a key. Solution: Try pressing different keys. Replace the batteries with two new AA batteries. Problem: The LED blinks when you press a key, but the device does not respond. Solution: Make sure that the remote control is aimed at your device and is not more than 40 feet away. Problem: The LED blinks one long blink while in SET mode. Solution: An entry error has occurred (for example, wrong key). Try entering the sequence again. Problem: The remote control does not control devices or commands are not working properly. Solution: Try all listed codes for the device. Make sure the device operates with an infrared remote control. Problem: No volume on a device. Solution: See "Changing volume lock" on page 18, and make sure that the volume is not locked to a different mode already. Problem: Channels do not change correctly when directly entering digits to change channels. Solution: If the original remote control required you to press Enter to change channels, press Enter on this remote after entering the channel number. Insignia NS-LCD52HD-09 52" LCD HD TV 20 www.insignia-products.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
20
Insignia NS-LCD52HD-09 52” LCD HD TV
www.insignia-products.com
To program a mode-dependent macro:
1
Press the device mode key (
TV
,
DVD
,
STB
,
or
AUX
).
2
Press and hold
SET
until the LED blinks
twice, then release.
3
Press
9 7 8
. The LED blinks twice.
4
Press the key you wish to assign to a macro.
5
Enter the series of commands you want the
macro to execute (up to 15 commands).
6
Press and hold
SET
until the red LED blinks
twice, then release.
Now, when you press the macro key, the
remote sends the series of commands you
have entered, but only if you are in the mode
you selected in Step 1. For example, you
could program the macro key to turn on both
your TV and cable box and select a particular
channel, but only if you are in TV mode. If you
are in DVD mode, this key does not execute
the macro you set up in TV mode.
7
To clear the macro, repeat Steps 1-6, but do
not enter a series of commands at Step 5.
Troubleshooting remote control
programming
Problem
: The LED does not blink when you
press a key.
Solution
: Try pressing different keys. Replace
the batteries with two new AA batteries.
Problem
: The LED blinks when you press a key,
but the device does not respond.
Solution
: Make sure that the remote control is
aimed at your device and is not more than 40
feet away.
Problem
: The LED blinks one long blink while in
SET mode.
Solution
: An entry error has occurred (for
example, wrong key). Try entering the sequence
again.
Problem
: The remote control does not control
devices or commands are not working properly.
Solution
: Try all listed codes for the device.
Make sure the device operates with an infrared
remote control.
Problem
: No volume on a device.
Solution
: See “Changing volume lock” on page
18, and make sure that the volume is not locked
to a different mode already.
Problem
: Channels do not change correctly
when directly entering digits to change channels.
Solution
: If the original remote control required
you to press
Enter
to change channels, press
Enter
on this remote after entering the channel
number.