Intel BLKDG43NB Product Specification - Page 51

Auxiliary Front Panel Power LED Header

Get Intel BLKDG43NB - MB 1333FSB DDR2 800 Aud+Lan SATA ATX PDF manuals and user guides
UPC - 735858201773
View all Intel BLKDG43NB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Technical Reference 2.2.2.5.2 Reset Switch Header Pins 5 and 7 can be connected to a momentary single pole, single throw (SPST) type switch that is normally open. When the switch is closed, the board resets and runs the POST. 2.2.2.5.3 Power/Sleep LED Header Pins 2 and 4 can be connected to a one- or two-color LED. Table 25 shows the possible states for a one-color LED. Table 26 shows the possible states for a two-color LED. Table 25. States for a One-Color Power LED LED State Description Off Power off/sleeping Steady Green Running Table 26. States for a Two-Color Power LED LED State Description Off Steady Green Steady Yellow Power off Running Sleeping NOTE The colors listed in Table 25 and Table 26 are suggested colors only. Actual LED colors are chassis-specific. 2.2.2.5.4 Power Switch Header Pins 6 and 8 can be connected to a front panel momentary-contact power switch. The switch must pull the SW_ON# pin to ground for at least 50 ms to signal the power supply to switch on or off. (The time requirement is due to internal debounce circuitry on the board.) At least two seconds must pass before the power supply will recognize another on/off signal. 2.2.2.6 Auxiliary Front Panel Power LED Header Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front panel header. Table 27. Auxiliary Front Panel Power LED Header Pin Signal Name In/Out Description 1 HDR_BLNK_GRN Out Front panel green LED 2 Not connected 3 HDR_BLNK_YEL Out Front panel yellow LED 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Technical Reference
51
2.2.2.5.2
Reset Switch Header
Pins 5 and 7 can be connected to a momentary single pole, single throw (SPST) type
switch that is normally open.
When the switch is closed, the board resets and runs the
POST.
2.2.2.5.3
Power/Sleep LED Header
Pins 2 and 4 can be connected to a one- or two-color LED.
Table 25 shows the
possible states for a one-color LED.
Table 26 shows the possible states for a two-color
LED.
Table 25.
States for a One-Color Power LED
LED State
Description
Off
Power off/sleeping
Steady Green
Running
Table 26.
States for a Two-Color Power LED
LED State
Description
Off
Power off
Steady Green
Running
Steady Yellow
Sleeping
±
NOTE
The colors listed in Table 25 and Table 26 are suggested colors only.
Actual LED
colors are chassis-specific.
2.2.2.5.4
Power Switch Header
Pins 6 and 8 can be connected to a front panel momentary-contact power switch.
The
switch must pull the SW_ON# pin to ground for at least 50 ms to signal the power
supply to switch on or off.
(The time requirement is due to internal debounce circuitry
on the board.)
At least two seconds must pass before the power supply will recognize
another on/off signal.
2.2.2.6
Auxiliary Front Panel Power LED Header
Pins 1 and 3 of this header duplicate the signals on pins 2 and 4 of the front panel
header.
Table 27.
Auxiliary Front Panel Power LED Header
Pin
Signal Name
In/Out
Description
1
HDR_BLNK_GRN
Out
Front panel green LED
2
Not connected
3
HDR_BLNK_YEL
Out
Front panel yellow LED