Intel D865GRH D865GRH_ProductGuide01_English. - Page 35

Installing and Removing an AGP Card, Installing an AGP Card, Removing the AGP Card

Get Intel D865GRH PDF manuals and user guides View all Intel D865GRH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Installing and Replacing Desktop Board Components Installing and Removing an AGP Card CAUTION When installing any AGP card in the desktop board, ensure that it is fully seated in the AGP connector before you power on the system. If the card is not fully seated in the AGP connector, an electrical short may result across the AGP connector pins. Depending on the over-current protection of the power supply, certain board components and/or traces may be damaged. The AGP connector supports 0.8 V (4x and 1x) and 1.5 V (8x) AGP cards. The desktop board has an integrated AGP card retention mechanism (RM). Installing an AGP Card Follow these instructions to install an AGP card: 1. Observe the precautions in "Before You Begin" on page 25. 2. Place the card in the AGP connector. 3. Press down on the card until it is completely seated in the AGP connector and the card retention notch snaps into place around the RM pin. 4. Secure the card's metal bracket to the chassis back panel with a screw. Removing the AGP Card Follow these instructions to remove the AGP card from the RM (see Figure 10): 1. Observe the precautions in "Before You Begin" on page 25. 2. Remove the screw (B) that secures the card's metal bracket (A) to the chassis back panel. 3. Push back on the RM lever (C), as shown in Figure 10, until the retention pin completely clears the notch in the card. 4. Pull the card straight up (D). B D A C OM15031 Figure 10. Removing the AGP Card 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Installing and Replacing Desktop Board Components
35
Installing and Removing an AGP Card
CAUTION
When installing any AGP card in the desktop board, ensure that
it is fully seated in the AGP
connector before you power on the system.
If the card is not fully seated in the AGP connector, an
electrical short may result across the AGP connector pins.
Depending on the over-current
protection of the power supply, certain board components and/or traces may be damaged.
The AGP connector supports 0.8 V (4x and 1x) and 1.5 V (8x) AGP cards.
The desktop board has
an integrated AGP card retention mechanism (RM).
Installing an AGP Card
Follow these instructions to install an AGP card:
1.
Observe the precautions in
“
Before You Begin
”
on page 25.
2.
Place the card in the AGP connector.
3.
Press down on the card until it is completely seated in the AGP connector and the card retention
notch snaps into place around the RM pin.
4. Secure the card
’
s metal bracket to the chassis back panel with a screw.
Removing the AGP Card
Follow these instructions to remove the AGP card from the RM (see Figure 10):
1.
Observe the precautions in
“
Before You Begin
”
on page 25.
2.
Remove the screw (B) that secures the card
’
s metal bracket (A) to the chassis back panel.
3.
Push back on the RM lever (C), as shown in Figure 10, until the retention pin completely clears
the notch in the card.
4.
Pull the card straight up (D).
OM15031
A
B
C
D
Figure 10.
Removing the AGP Card