Intel P4000S Service Guide - Page 41

Installing Hot-swap Hard Drive

Get Intel P4000S PDF manuals and user guides View all Intel P4000S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Hardware Installations and Upgrades 8. Install the 4x3.5'' Hot-swap Hard drives cage. For instructions, see "installing 4x3.5'' Hot-swap Hard Drive Cage". 9. Install the front bezel. For instructions, see "Installing the Front Bezel". 10. Install the chassis cover. For instructions, see "Installing the Chassis Cover". 11. Plug all peripheral devices and the AC power cable into the server. 12. Power up the server. Installing Hot-swap Hard Drive Installing 3.5" Hard Disk Drive CAUTION The 3.5" hard disk drive can be a SSD or SAS and SATA. Refer to your server board or system documentation to determine SSD/SAS/SATA support for your server system. 1. Remove the four screws securing the 2.5" HDD interface bracket and remove the 2.5" HDD interface bracket. Figure 39. Removing the 2.5" HDD interface bracket from Carrier 2. Install the 3.5" hard disk drive using the same four screws as shown. Make sure the connector end of the drive matches the backplane connector. Intel® Server Chassis P4000S Service Guide 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Hardware Installations and Upgrades
Intel
®
Server Chassis P4000S Service Guide
29
8.
Install the 4x3.5
''
Hot-
swap Hard drives cage. For instructions, see “installing 4x3.5
''
Hot-swap Hard
Drive Cage
”
.
9.
Install the front bezel. For i
nstructions, see “Installing the Front
Bezel”.
10. Install th
e chassis cover. For instructions, see “Installing the Chassis Cover”.
11. Plug all peripheral devices and the AC power cable into the server.
12. Power up the server.
Installing Hot-swap Hard Drive
Installing 3.5" Hard Disk Drive
CAUTION
The 3.5" hard disk drive can be a SSD or SAS and SATA. Refer to your server board
or system documentation to determine SSD/SAS/SATA support for your server
system.
1.
Remove the four screws securing the 2.5" HDD interface bracket and remove the 2.5" HDD interface
bracket.
Figure 39. Removing the 2.5" HDD interface bracket from Carrier
2.
Install the 3.5" hard disk drive using the same four screws as shown. Make sure the connector end of the
drive matches the backplane connector.