Intel S5500HCV Service Guide - Page 51

System Boots when Installing PCI Card, Problems with Newly Installed Application Software

Get Intel S5500HCV - Server Board Motherboard PDF manuals and user guides
UPC - 735858207508
View all Intel S5500HCV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Troubleshooting Diagnostics pass but the connection fails  Make sure the network cable is securely attached.  Make sure you specify the correct frame type in your NET.CFG file. The controller stopped working when an add-in adapter was installed  Make sure the cable is connected to the port from the on-board network controller.  Make sure your BIOS is current. For a link to the current version, see "Additional Information and Software".  Make sure the other adapter supports shared interrupts. Make sure your operating system supports shared interrupts.  Try reseating the add-in adapter. The add-in adapter stopped working without apparent cause  Try reseating the adapter first; then try a different slot if necessary.  The network driver files may be corrupt or deleted. Delete and then reinstall the drivers.  Run the diagnostics. System Boots when Installing PCI Card System Server Management features require full-time "standby" power. This means some parts of the system have power going to them whenever the power cord is plugged in, even if you turned-off the system power with the power button on the front panel. If you install a PCI card with the AC power cord plugged in, a signal may be sent to command the system to boot. Before installing a PCI card, you should always:  Turn off the server power by using the power button on the front of the system.  Unplug the AC power cord(s) from the server. Problems with Newly Installed Application Software Problems that occur when you run new application software are usually related to the software-not the server hardware. Faulty equipment is unlikely, especially if other software runs correctly. Check the following: 1. Make sure the system meets the minimum hardware requirements for the software. See the software documentation. 2. Make sure the software is properly installed and configured for the system. See the software documentation. 3. Use only an authorized copy. Unauthorized copies often do not work. 4. If you run the software from a diskette, CD-ROM, or DVD-ROM, try a different diskette. 5. Make sure the correct device drivers are installed. If the problems persist, contact the software vendor's customer service representative. Intel® Server Board S5520HC and S5500HCV Service Guide 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Troubleshooting
Intel
®
Server Board S5520HC and S5500HCV Service Guide
51
Diagnostics pass but the connection fails
Make sure the network cable is securely attached.
Make sure you specify the correct frame type in your NET.CFG file.
The controller stopped working when an add-in adapter was installed
Make sure the cable is connected to the port from the on-board network controller.
Make sure your BIOS is current. For a link to the current version, see
“Additional Information and Software”
.
Make sure the other adapter supports shared interrupts. Make sure your operating system supports shared
interrupts.
Try reseating the add-in adapter.
The add-in adapter stopped working without apparent cause
Try reseating the adapter first; then try a different slot if necessary.
The network driver files may be corrupt or deleted. Delete and then reinstall the drivers.
Run the diagnostics.
System Boots when Installing PCI Card
System Server Management features require full-time “standby” power. This means some parts of the system have
power going to them whenever the power cord is plugged in, even if you turned-off the system power with the power
button on the front panel. If you install a PCI card with the AC power cord plugged in, a signal may be sent to
command the system to boot.
Before installing a PCI card, you should always:
Turn off the server power by using the power button on the front of the system.
Unplug the AC power cord(s) from the server.
Problems with Newly Installed Application Software
Problems that occur when you run new application software are usually related to the software—not the server
hardware. Faulty equipment is unlikely, especially if other software runs correctly.
Check the following:
1.
Make sure the system meets the minimum hardware requirements for the software. See the software
documentation.
2.
Make sure the software is properly installed and configured for the system. See the software documentation.
3.
Use only an authorized copy. Unauthorized copies often do not work.
4.
If you run the software from a diskette, CD-ROM, or DVD-ROM, try a different diskette.
5.
Make sure the correct device drivers are installed.
If the problems persist, contact the software vendor’s customer service representative.