Intel SE7501CW2 Product Guide - Page 76

CD-ROM Drive Activity Light Does Not Light, Cannot Connect to a Server, Problems with Network - server board drivers

Get Intel SE7501CW2 - E7501 DUAL PGA604 XEON 533MHZ PDF manuals and user guides
UPC - 735858160308
View all Intel SE7501CW2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

CD-ROM Drive Activity Light Does Not Light Check the following: Are the CD-ROM drive's power and signal cables properly installed? Are all relevant switches and jumpers on the drive set correctly? Is the drive properly configured? Cannot Connect to a Server Make sure you are using the drivers that are shipped on the system Configuration Software CD for the onboard network controller. Make sure the driver is loaded and the protocols are bound. Make sure the network cable is securely attached to the connector at the system back panel. If the cable is attached but the problem persists, try a different cable. Make sure the hub port is configured for the same duplex mode as the network controller. Check with your LAN administrator about the correct networking software that needs to be installed. If you are directly connecting two servers (no hub), you will need a crossover cable (see your hub documentation for more information on crossover cables). Check the network controller LEDs that are visible through an opening at the system back panel. Problems with Network The server hangs when the drivers are loaded. Change the PCI BIOS interrupts. Try the "PCI Installation Tips" below. Diagnostics pass but the connection fails. Make sure the network cable is securely attached. Make sure you specify the correct frame type in your NET.CFG file. The Activity LED does not light. The network activity light is not connected to the Server Board SE7501CW2. 76 Intel Server Board SE7501CW2 Product Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
76
Intel Server Board SE7501CW2 Product Guide
CD-ROM Drive Activity Light Does Not Light
Check the following:
±
Are the CD-ROM drive’s power and signal cables properly installed?
±
Are all relevant switches and jumpers on the drive set correctly?
±
Is the drive properly configured?
Cannot Connect to a Server
±
Make sure you are using the drivers that are shipped on the system Configuration Software CD
for the onboard network controller.
±
Make sure the driver is loaded and the protocols are bound.
±
Make sure the network cable is securely attached to the connector at the system back panel.
If
the cable is attached but the problem persists, try a different cable.
±
Make sure the hub port is configured for the same duplex mode as the network controller.
±
Check with your LAN administrator about the correct networking software that needs to be
installed.
±
If you are directly connecting two servers (no hub), you will need a crossover cable (see your
hub documentation for more information on crossover cables).
±
Check the network controller LEDs that are visible through an opening at the system back
panel.
Problems with Network
The server hangs when the drivers are loaded.
±
Change the PCI BIOS interrupts.
Try the “PCI Installation Tips” below.
Diagnostics pass but the connection fails.
±
Make sure the network cable is securely attached.
±
Make sure you specify the correct frame type in your NET.CFG file.
The Activity LED does not light.
The network activity light is not connected to the Server Board SE7501CW2.