Invacare TRSX52FBP User Manual - Page 36

Bolt-In-Place

Page 36 highlights

5 FRONT RIGGINGS Bolt-In-Place  This procedure applies to the swingaway front riggings and swingaway elevating legrest. 1. Remove the swingaway front rigging. Refer to Installing/Removing Front Riggings on page 34.  Lay the front rigging assembly on a flat surface to simplify this procedure. 2. Pull the cam lock lever up to the unlocked position. 3. Using a screw driver to hold the threaded rivet in position, remove the button head screw from the threaded rivet. 4. Remove the threaded rivet and button head screw securing the footplate assembly to the front rigging support. 5. Adjust the footplate assembly height by aligning the desired adjustment holes in the upper front rigging support and lower footplate assembly. 6. From the outside of the swingaway front rigging, insert the threaded rivet through both the front rigging support and the footplate assembly. 7. From the inside of the swingaway front rigging, insert the button head screw through the appropriate adjustment hole and thread into the threaded rivet. 8. Using a screwdriver to hold the threaded rivet in position, securely tighten the button head screw. Torque to 32 in-lbs. 9. Rotate cam lock lever down to locked position. 10. Repeat STEPS 1-9 to adjust the remaining footrest. Front Rigging Support  Swingaway footrest shown Adjustment Hole Front Rigging Support Button Head Screw Threaded Rivet Button Head Screw Cam Lock Lever Adjustment Hole Threaded Rivet Footplate Assembly Footplate Assembly Inside of Swingaway Front Rigging Outside of Swingaway Front Rigging Invacare® Tracer® SX5 Wheelchair FIGURE 3 Adjusting Footplate Height - Bolt-In-Place 36 Part No. 1110550

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84

5
FRONT RIGGINGS
Invacare® Tracer® SX5 Wheelchair
36
Part No. 1110550
Bolt-In-Place
1.
Remove the swingaway front rigging. Refer to Installing/Removing Front Riggings
on page 34.
2.
Pull the cam lock lever up to the unlocked position.
3.
Using a screw driver to hold the threaded rivet in position, remove the button head screw from the threaded rivet.
4.
Remove the threaded rivet and button head screw securing the footplate assembly to the front rigging support.
5.
Adjust the footplate assembly height by aligning the desired adjustment holes in the upper front rigging support and lower footplate assembly.
6.
From the outside of the swingaway front rigging, insert the threaded rivet through both the front rigging support and the footplate assembly.
7.
From the inside of the swingaway front rigging, insert the button head screw through the appropriate adjustment hole and thread into the threaded rivet.
8.
Using a screwdriver to hold the threaded rivet in position, securely tighten the button head screw. Torque to 32 in-lbs.
9.
Rotate cam lock lever down to locked position.
10.
Repeat STEPS 1-9 to adjust the remaining footrest.
FIGURE 3
Adjusting Footplate Height - Bolt-In-Place
This procedure applies to the swingaway front riggings and swingaway elevating legrest.
Lay the front rigging assembly on a flat surface to simplify this procedure.
Front Rigging Support
Button Head Screw
Threaded Rivet
Footplate Assembly
Footplate
Assembly
Threaded Rivet
Front Rigging Support
Button Head
Screw
Adjustment
Hole
Inside of Swingaway Front Rigging
Adjustment Hole
Cam Lock Lever
Outside of Swingaway Front Rigging
Swingaway
footrest shown