JVC C11U Instruction Manual - Page 30

Motion Detection Setting

Get JVC C11U - VN Network Camera PDF manuals and user guides
UPC - 046838325670
View all JVC C11U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Preparations (Step 2 Setting the Network) 2-4 Other Settings with V.Networks Setup Tool [3. Motion Detection Setting] This section describes the setting of the motion detection function which enables VN-C11 to trigger an alarm when motion is detected in a specified area. Motion is monitored while being compared to the reference image.The area within which the function is effective can be set in the following procedure. (This function cannot be set for MPEG4.) 1. Start up [V.Networks SetupTool]. Select [Alarm] and then enable [Motion Detection Alarm]. (☞Page 28 [Alarm Setting]) 2. Select [Motion Detect] of [V.Networks Setup Tool]. Select the desired monitoring area by clicking and holding down the left button of the mouse and dragging it. The selected area is displayed in yellow. Click the right button of the mouse and, while holding it down, drag the mouse to cancel a monitoring area. The area in which motion has been detected is displayed in red. The [Detail] button is used for more detailed settings. Note ● A selected area is only for reference. To ensure accuracy, perform operation check. ● One screen is divided in 300 (20x15) blocks. Adjust magnification of the lens so that the monitoring area (object) covers more than one block. Caution The motion detection function is not designed to prevent burglary or fire. It may not function properly depending on the condition of the object or settings described in this document. In no case, shall JVC be liable for any accidents and/or damage caused. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
30
Preparations (Step 2 Setting the Network)
This section describes the setting of the motion detection function which enables VN-C11 to
trigger an alarm when motion is detected in a specified area. Motion is monitored while being
compared to the reference image. The area within which the function is effective can be set in
the following procedure.
(This function cannot be set for MPEG4.)
1.
Start up [V.Networks Setup Tool]. Select [Alarm] and then enable [Motion Detection Alarm].
(
☞
Page 28 [Alarm Setting])
2.
Select [Motion Detect] of [V.Networks Setup Tool].
Note
●
A selected area is only for reference.
To ensure accuracy, perform operation check.
●
One screen is divided in 300 (20x15) blocks.
Adjust magnification of the lens so that the
monitoring area (object) covers more than one block.
Caution
The motion detection function is not designed to prevent burglary or fire.
It may not function
properly depending on the condition of the object or settings described in this document.
In no
case, shall JVC be liable for any accidents and/or damage caused.
Select the desired monitoring area by click-
ing and holding down the left button of the
mouse and dragging it.
The selected area
is displayed in yellow.
Click the right button of the mouse and,
while holding it down, drag the mouse to
cancel a monitoring area.
The [Detail] button is used for more detailed
settings.
2-4 Other Settings with V.Networks Setup Tool [3. Motion Detection Setting]
The area in which motion has been detected
is displayed in red.