JVC GR-DVF31 Instruction Manual - Page 12

Recording

Get JVC GR-DVF31 - Web Camera PDF manuals and user guides
UPC - 046838157714
View all JVC GR-DVF31 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

12 EN Recording Start/Stop Button Power Switch Display 25 min During shooting Tape remaining time indicator (Approximate) min 90 min (Now calculating) 0 min (Blinking) 89 min 1 min (Blinking) 3 min 2 min (Blinking) RECORDING Basic Recording Shooting While Watching The Viewfinder NOTE: You should already have performed the procedures listed below. If not, do so before continuing. ● Power (੬ pg. 6) ● Load A Cassette (੬ pg. 9) ● Recording Mode Setting (੬ pg. 10) ● Grip Adjustment (੬ pg. 11) ● Viewfinder Adjustment (੬ pg. 11) 1 Make sure the LCD monitor is closed and locked. Press in the tabs on the lens cap to remove it, then set the Power Switch to " " or " ". The power lamp lights and the camcorder enters the Record-Standby mode. "PAUSE" is displayed in the viewfinder. 2 Press the Recording Start/Stop Button. " " appears in the viewfinder while recording is in progress. 3 Press the Recording Start/Stop Button again to stop recording. The camcorder re-enters the RecordStandby mode. 180° 90° MENU/ BRIGHT Dial BRIGHT - - - - -6- - - - - Power Switch Recording Start/Stop Button To Adjust The Brightness Of The Display .... rotate MENU/BRIGHT until the brightness indicator on the display moves and the appropriate brightness is reached. •It is also possible to adjust the brightness of the viewfinder. Shooting While Watching The LCD Monitor Before the following steps, perform the procedures listed in the above note. 1 Make sure the LCD monitor is fully open. Press in the tabs on the lens cap to remove it, then set the Power Switch to " " or " ". The power lamp lights and the camcorder enters the Record-Standby mode. "PAUSE" is displayed in the LCD monitor. 2 Tilt the LCD monitor upward/downward for best viewability and press the Recording Start/Stop Button. " " appears in the LCD monitor while recording is in progress. 3 Press the Recording Start/Stop Button again to stop recording. The camcorder re-enters the RecordStandby mode. NOTE: When you use the LCD monitor outdoors in direct sunlight, the LCD monitor may be difficult to see. If this happens, use the viewfinder instead.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
12
EN
180
°
90
°
BRIGHT
– – – – –
6
– – – – –
25 min
90 min
89 min
3 min
2 min
1 min
0 min
min
RECORDING
Basic Recording
Shooting While Watching The
Viewfinder
NOTE:
You should already have performed the procedures listed
below. If not, do so before continuing.
●
Power (
Z
pg. 6)
●
Load A Cassette (
Z
pg. 9)
●
Recording Mode Setting (
Z
pg. 10)
●
Grip Adjustment (
Z
pg. 11)
●
Viewfinder Adjustment (
Z
pg. 11)
1
Make sure the LCD monitor is closed and locked.
Press in the tabs on the lens cap to remove it, then set
the Power Switch to “
” or “
”. The power lamp
lights and the camcorder enters the Record-Standby
mode. “PAUSE” is displayed in the viewfinder.
2
Press the Recording Start/Stop Button. “
” appears
in the viewfinder while recording is in progress.
3
Press the Recording Start/Stop Button again to stop
recording. The camcorder re-enters the Record-
Standby mode.
Power Switch
Shooting While Watching The
LCD Monitor
Before the following steps, perform the procedures listed
in the above note.
1
Make sure the LCD monitor is fully open. Press in the
tabs on the lens cap to remove it, then set the Power
Switch to “
” or “
”.
The power lamp lights and
the camcorder enters the Record-Standby mode.
“PAUSE” is displayed in the LCD monitor.
2
Tilt the LCD monitor upward/downward for best
viewability and press the Recording Start/Stop Button.
“
” appears in the LCD monitor while recording is
in progress.
3
Press the Recording Start/Stop Button again to stop
recording. The camcorder re-enters the Record-
Standby mode.
NOTE:
When you use the LCD monitor outdoors in direct
sunlight, the LCD monitor may be difficult to see. If this
happens, use the viewfinder instead.
Power Switch
Recording Start/Stop
Button
MENU/
BRIGHT Dial
Recording
Start/Stop Button
Tape remaining time
indicator (Approximate)
(Now calculating)
(Blinking)
(Blinking)
(Blinking)
To Adjust The Brightness Of The Display
....
rotate
MENU/BRIGHT
until the brightness
indicator on the display moves and the
appropriate brightness is reached.
• It is also possible to adjust the brightness of
the viewfinder.
Display
During shooting