JVC GR-DVF31 Instruction Manual - Page 22

Fade/Wipe Effects

Get JVC GR-DVF31 - Web Camera PDF manuals and user guides
UPC - 046838157714
View all JVC GR-DVF31 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

22 EN RECORDING Advanced Features (cont.) Fade/Wipe Effects These effects let you make pro-style scene transitions. Use them to spice up the transition from one scene to the next. You can also vary transitions from scene to scene. IMPORTANT: Some Fade/Wipe Effects cannot be used with certain modes of Program AE with special effects (੬ pg. 24). If an unusable Fade/Wipe Effect is selected, its indicator blinks. MENU/BRIGHT Dial FADE/WIPE SELECTION and ) Fade or Wipe works when recording is started or when you stop recording. 1 Set the Power Switch to " ". 2 Press MENU/BRIGHT. The Recording Menu appears. 3 Rotate MENU/BRIGHT to move the highlight bar to "FADER/WIPE", then press it. 4 Rotate MENU/BRIGHT to move the highlight bar to the desired function, then press it. •The FADER/WIPE Menu disappears and the effect is reserved. The indicator representing the selected effect appears. Power Switch 5 Press the Recording Start/Stop Button to activate the Fade-in/out or Wipe-in/out. Recording Start/Stop Button NOTES: ● You can extend the length of a Fade or Wipe by pressing and holding the Recording Start/ Stop Button. ● If the power is turned off after a scene is finished recording, the stored point is erased, disabling the Picture Wipe/Dissolve combination. When this happens, the Picture Wipe/ Dissolve indicator blinks. Also note that power shuts off automatically if 5 minutes elapse in the Record-Standby mode. ● The sound at the end of the last recorded scene is not stored. PICTURE WIPE OR DISSOLVE SELECTION and ) The Picture Wipe or Dissolve works when recording is started. 1 Follow steps 1 through 4 above. 2 Engage the Record-Standby mode. If you select Picture Wipe/Dissolve during recording . . . .... press the Recording Start/Stop Button when one scene is finished. The point at which the scene ended is stored in memory. If you select Picture Wipe/Dissolve during RecordStandby mode . . . .... press the Recording Start/Stop Button to start recording and press it again when one scene is finished. The point at which the scene ended is stored in memory. If you select Picture Wipe/Dissolve during RecordStandby mode after performing a Picture Wipe/ Dissolve . . . .... the point at which the scene ended is already stored in memory. 3 If you start recording a new scene within 5 minutes of the end of the previous recording (without having turned the camcorder's power off), the previous scene wipes out, revealing the new scene.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
22
EN
RECORDING
Advanced Features (cont.)
Fade/Wipe Effects
These effects let you make pro-style scene
transitions. Use them to spice up the transition
from one scene to the next. You can also vary
transitions from scene to scene.
IMPORTANT:
Some Fade/Wipe Effects cannot be used with
certain modes of Program AE with special
effects (
Z
pg. 24). If an unusable Fade/Wipe
Effect is selected, its indicator blinks.
Recording Start/Stop Button
MENU/BRIGHT Dial
Power Switch
FADE/WIPE SELECTION (
,
,
,
,
,
,
,
,
,
and
)
Fade or Wipe works when recording is started or when
you stop recording.
1
Set the Power Switch to “
”.
2
Press
MENU/BRIGHT
. The Recording Menu appears.
3
Rotate
MENU/BRIGHT
to move the highlight bar to
“FADER/WIPE”, then press it.
4
Rotate
MENU/BRIGHT
to move the highlight bar to
the desired function, then press it.
•The FADER/WIPE Menu disappears and the effect is
reserved. The indicator representing the selected
effect appears.
5
Press the Recording Start/Stop Button to activate the
Fade-in/out or Wipe-in/out.
PICTURE WIPE OR DISSOLVE SELECTION
(
,
,
,
,
,
and
)
The Picture Wipe or Dissolve works when recording is
started.
1
Follow steps
1
through
4
above.
2
Engage the Record-Standby mode.
If you select Picture Wipe/Dissolve during
recording . . .
....
press the Recording Start/Stop Button when one
scene is finished. The point at which the scene
ended is stored in memory.
If you select Picture Wipe/Dissolve during Record-
Standby mode . . .
....
press the Recording Start/Stop Button to start
recording and press it again when one scene is
finished. The point at which the scene ended is
stored in memory.
If you select Picture Wipe/Dissolve during Record-
Standby mode after performing a Picture Wipe/
Dissolve . . .
....
the point at which the scene ended is already
stored in memory.
3
If you start recording a new scene within 5 minutes of
the end of the previous recording (without having
turned the camcorder’s power off), the previous scene
wipes out, revealing the new scene.
NOTES:
●
You can extend the length of a Fade or Wipe
by pressing and holding the Recording Start/
Stop Button.
●
If the power is turned off after a scene is
finished recording, the stored point is erased,
disabling the Picture Wipe/Dissolve combina-
tion. When this happens, the Picture Wipe/
Dissolve indicator blinks. Also note that
power shuts off automatically if 5 minutes
elapse in the Record-Standby mode.
●
The sound at the end of the last recorded
scene is not stored.