JVC KD-R870BT Instruction Manual - Page 25

AUDIO SETTINGS Default: XX EQ SETTING EQ PRESET Select a preset equalizer suitable to the music genre. (Select [USER] to use the settings made in [EASY EQ] or [PRO EQ].) FLAT / HARD ROCK / POP / HIP HOP / R&B / JAZZ / CLASSICAL / USER EASY EQ Adjust your own sound settings. The settings are stored to [USER]. • The settings made may affect the current settings of [PRO EQ]. SUB.W SP*1*2: 00 to +06 (Default: 03 SUB.W *1*3: -50 to +10 00 BASS LVL: -09 to +09 00 MID LVL: -09 to +09 00 TRE LVL: -09 to +09 00) PRO EQ Adjust your own sound settings. The settings are stored to [USER]. • The settings made may affect the current settings of [EASY EQ]. 62.5HZ LVL -09 to +09 (00): Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.) BASS EXT ON: Turns on the extended bass. ; BASS EXT OFF: Cancels. 100HZ / 160HZ / 250HZ / 400HZ / 630HZ / 1KHZ / 1.6KHZ / 2.5KHZ / 4KHZ / 6.3KHZ / 10KHZ / 16kHZ LVL -09 to +09 (00): (Refer above) Q FACTOR Q 1.35/ Q 1.50/ Q 2.00: Adjust the quality factor. AUDIO BASS BOOST +01 - +05: Selects your preferred bass boost level. ; OFF: Cancels. LOUD 01 / 02: Boosts low or high frequencies to produce a well-balanced sound at low volume. ; OFF: Cancels. SUB.W LEVEL*1 SPK-OUT*2 (Not applicable when 3-way crossover is selected.) 00 to +06 (+03): Adjusts the output level of the subwoofer connected via speaker lead. ( 34, 35) PRE-OUT*3 -50 to +10 (00): Adjusts the output level of the subwoofer connected to the lineout terminals (SW or REAR/SW) through an external amplifier. ( 34, 35) SUB.W *3 ON / OFF: Turns on or off the subwoofer output. FADER (Not applicable when 3-way crossover is selected.) R15 - F15 (00): Adjusts the front and rear speaker output balance. BALANCE *4 L15 - R15 (00): Adjusts the left and right speaker output balance. VOL ADJUST -15 - +06 (00): Preset the initial volume level of each source (compared to the FM volume level). Before adjustment, select the source you want to adjust. AMP GAIN LOW POWER: Limits the maximum volume level to 25. (Select if the maximum power of each speaker is less than 50 W to prevent damaging the speakers.) ; HIGH POWER: The maximum volume level is 35. SPK/PRE OUT (Not applicable when 3-way crossover is selected.) Depending on the speaker connection method, select the appropriate setting to get the desired output. ( 22, Speaker output settings) SPK SIZE X ' OVER Depending on the crossover type you have selected (see [X ' OVER TYPE] below), 2-way crossover or 3-way crossover setting items will be shown. ( 23, Crossover settings) By default, 2-way crossover type is selected. X ' OVER TYPE Caution: Adjust the volume before changing the X ' OVER TYPE to avoid the sudden increase or decrease of the output level. X ' OVER 2-WAY (Displayed only when [X ' OVER 3-WAY] is selected) YES: Selects two way crossover type. ; NO: Cancels. X ' OVER 3-WAY (Displayed only when [X ' OVER 2-WAY] is selected) YES: Selects three way crossover type. ; NO: Cancels. *1 Displayed only when [SUB.W] is set to [ON]. *2 For 2-way crossover: Displayed only when [SPK/PRE OUT] is set to [SUB.W/SUB.W]. ( 22) *3 For 2-way crossover: Displayed only when [SPK/PRE OUT] is set to [REAR/SUB.W] or [SUB.W/ SUB.W]. ( 22) *4 This adjustment will not affect the subwoofer output. ENGLISH 21