JVC TM-1650SDU TM-1650SDU monitor instruction manual (358KB) - Page 8

HOW TO USE THE MENU FUNCTIONS DISPLAY AND SELECTION IN THE SCREEN MODE (SETTING) You can set the following menu items. Set them depending on your needs. • SHARPNESS • COLOR TEMP. • COLOR SYSTEM • ASPECT RATIO • RGB/COMPONENT • COMPO. LEVEL • BLUE CHECK 1. Press the MENU button. The screen is displayed. * The screen automatically disappears when no operation is MENU performed after about 5 minutes. 2. Press the PHASE ( ) or CHROMA ( ) button to select MENU items. A selection mark (3) is put next to the selected item. PHASE CHROMA SHARPNESS COLOR TEMP. COLOR SYSTEM ASPECT RATIO RGB/COMPONENT COMPO. LEVEL BLUE CHECK Front panel button Function displayed Contents PHASE ( ) ∞ Forward selection mark (3) CHROMA ( ) 5 Reverse selection mark (3) 3. Press the VOLUME/SELECT button to set. - + VOLUME/SELECT Front panel button VOLUME/ SELECT (+) VOLUME/ SELECT (-) Function displayed + 3 - 2 Contents Increase (to max. value) Forward the setting value Decrease (to min. value) Reverse the setting value Menu items SHARPNESS COLOR TEMP. COLOR SYSTEM ASPECT RATIO RGB/COMPONENT Purpose Picture sharpness Color temperature of white balance Color system Aspect ratio Input RGB/COMPONENT/SDI signal system Setting range 00 +1 +39 +40 9300 6500 AUTO NTSC AUTO PAL 4 - 3 16 - 9 RGB COMPO. SDI COMPO. LEVEL BLUE CHECK Component or SDI level Blue check ON/OFF +01 0 -01 OFF ON +9 +10 -39 -40 * In normal use, leave the COLOR SYSTEM setting to AUTO. If the receiving condition is not good in AUTO position, set it to the exclusive mode corresponding to the receiving color system (NTSC or PAL). * COMPO. LEVEL can be set for component input and SDI input independently. 4. If you want to set the other menu items, repeat procedures 2 and 3. 5. Press the MENU button to quit. Front panel button Function displayed Contents MENU MENU EXIT Quit (or Release) the screen screen 1 < MENU > ‰ SHARPNESS : 00 COLOR TEMP. : 6500 COLOR SYSTEM : AUTO ASPECT RATIO : 4-3 RGB/COMPONENT : RGB COMPO. LEVEL : 00 BLUE CHECK : OFF 2 3 EXIT 4 - + PHASE CHROMA BRIGHT CONTRAST MENU VOLUME/SELECT 1 Selection mark (3): Indicates the menu item you select. 2 Menu item: Menu items you can select. 3 Setting display: Indicates the current settings (value). 4 Function display: The functions of the front panel buttons (7 buttons on the left) correspond to the function displayed. Function displayed Contents ∞ Forward the menu item. 5 Reverse the menu item. - Lower the adjustment value. (to the minimum) + Raise the adjustment value. (to the maximum) 3 Forward the setting value. 2 Reverse the setting value. EXIT Exits the screen. Notes: ● When the screen aspect ratio is set to 16 - 9 (16:9) in ASPECT RATIO, the picture will be vertically reduced. ● When REMOTE is displayed in the ASPECT RATIO or RGB COMPONENT status, it is not possible to set these items because ASPECT REMOTE or INPUT REMOTE in the is set to valid. Use the external control function or set ASPECT REMOTE or INPUT REMOTE to invalid (OFF) to make setting possible. ● The BLUE CHECK function is not memorized. After the power is turned off and on again, BLUE CHECK is automatically set to OFF. Refer to page 9 for more information about the BLUE CHECK function. ● When selecting COMPONENT or SDI, adjust CHROMA GAIN (COLOR) in the COMPO. LEVEL item first, then input a standard signal from the device used with the monitor and adjust CHROMA GAIN with BLUE CHECK. Refer to page 9 for more information about initializing COMPO. LEVEL. 8