Jensen VM9213 Operation Manual - Page 11
Power On / Off, Audible Beep Confirmation, Playing Source Selection, Volume Adjustment, Steering - accessories
UPC - 043258304391
View all Jensen VM9213 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 11 highlights
VM9213 OPERATING INSTRUCTIONS Power On / Off Press the /SRC button (6) on the unit (or the button (4) on the remote control) to turn the unit on. The buttons on the front of the unit light up and the current mode status appears in the LCD (7). You can also turn on the unit by pressing the OPEN button (1) and opening the TFT screen. Press and hold the button to power off the unit.The monitor is drawn back into the main compartment. Audible Beep Confirmation An audible beep tone confirms each function selection. The Beep tone can be disabled through the Setup menu. Mute Press the MUTE button (3) on the remote control to mute the volume from the unit. Press the MUTE button again to restore the volume. If the monitor is closed, "MUTE" is displayed on the LCD. When the monitor is open, the yellow volume icon appears on the TFT with an "X" through it. Adjusting the volume or using any of the audio setup features cancels the mute function. Playing Source Selection Press the SRC button (6) on the front panel or the SRC button (8) on the remote to change between available playing sources. The playing mode is displayed on the TFT and LCD screens. External peripheral devices can be connected to this unit via the rear RCA inputs or the A/V INPUT connector (10) on the front of the unit. Select "AUX-IN1" to access an auxiliary device connected to the A/V INPUT on the front panel. Select "AUX IN2" mode to access a device connected to the rear AUX IN connectors. EJECT A/V INPUT 1 Right Audio 2 Left Audio 3 Ground 4 Video 3.5mm Media Cable (included) Connect the external device to the 3.5mm Media Cable and then plug the cable into the A/V INPUT connector (10) on the front of the radio. Select "AUX IN1" mode to access an auxiliary device connected to the A/V INPUT on the front of the radio. You cannot directly control external devices connected to the A/V INPUT. Volume Adjustment To increase or decrease the volume level, turn the rotary encoder (5) on the front panel or press the VOL+/ VOLbuttons (15, 16) on remote control. The volume ranges from "0" to "40". The LCD or TFT screen displays the volume level for 3 seconds. Steering Wheel Control (SWC) The VM9213 is compatible with the PAC (Pacific Accessory Corporation) steering wheel control adapter SWI-PS. A 3.5mm female connector (labeled "SWC Interface") on the back of the head unit allows connectivity to the PAC adapter. Please refer to the instructions included with the PAC adapter for detailed installation information. SWC Functions The following controls are available for most vehicles: 1. Vol Down 2. Vol Up 3. Mute 4. Seek Down / Previous Track / ** Preset Down 5. Seek Up / Next Track / ** Preset Up 6. SRC (Source) 7. ** Select 8. ** Select 9. Band ** If additional steering wheel control buttons are available on the vehicle, function 7 / 8 may be assigned the "Select" feature. This feature / function may not be available on some vehicles. Select Operation If "Select" (function 7 or 8) is held down and function 4 is pressed momentarily, Preset Up will be selected. If "Select" (function 7 or 8) is held down and function 5 is pressed momentarily, Preset Down will be selected. Audio Control Menu The Audio Control feature allows you to easily adjust your audio system to meet the acoustical characteristics of your vehicle, which vary depending on the type of vehicle and its measurements. Proper setting of the Fader and Balance boosts the effects of the cabin equalizer. Press the EQ button on the touch screen to display the audio menu. +14 - 0- EQ User 0- - FAD BAL F L R -14 - -14 - R BASS MID TREB SUB User To adjust an audio feature: 1. Use the touchscreen, or press the buttons (14, 22) on the remote control to highlight the audio feature to be adjusted. 2. Touch the screen to select the highlighted option. 3. Touch the +/- buttons on the screen or press the ||, >>, or